I for one like the new interface. On the scanner, I'm finding it easier to build histograms. I really like the "limit list to the activated PID" feature. I also like that multiple copy feature whereby you can bring entire of pages over to a tune file.
Dumb question, but on the F_body 2002 OS, looks like the integral high and low for the rolling idle air descriptors are reversed? The integral High says this is the air added when idle speed is low, and integral Low says this is the air added when idle speed is high. Again, this is the rolling idle tables under the cracker and follower, not the main integral tables on the RPM page
Commanded gear still broken on 3.0.22. This time a 2009 Silverado 4L60E. It will hold first gear, but as soon as you click second it quits working.
www.crawford-racing.com
Home of the original and best selling CR-Fueler plug and play port injection controller kits for all GM Gen V direct injection platforms.
Anybody else noticing way longer flash times? Gen IV ECMs usually took 30 seconds start to finish with 2.24, but with 3.0 they are taking damn near a full minute.
DSX Tuning - Authorized HP Tuners Dealer
http://www.dsxtuning.com
http://www.facebook.com/dsx.tuning
Just say no to bull s***.
IF YOU WANT HELP, POST A FILE!
Mine just seems to be inconsistent. Sometimes they're fast, sometimes they're not. Could be my imagination..
3.0 obeys the manufacturer requested timing. 2.24 did not.
We got this guy Not Sure, ...
www.crawford-racing.com
Home of the original and best selling CR-Fueler plug and play port injection controller kits for all GM Gen V direct injection platforms.
Good deal! I actually had it happen again a few days ago. The gauges and all would not come back on but somehow HPT finally connected and finished writing the tune anyways. It was fine after that. In my case I think the battery voltage was too low.. I flashed on a cold cold morning (20*F) on a car that hadn't been started in over a week so that probably wasn't the brightest idea
I cant seem to find injector duty cycle in either scanner or editor on 3.0. any help? thanks
Has there been any advance on getting the histograms to read on more than one line when logging spark retard and spark advance whilst plotting rpm vrs cylinder air mass (g). This software is costing me a lot of productivity.
In the Scanner....Tools>Math Parameters>Maths - Predefined>Fuel Flow. They don't get populated into the Channel table anymore, only in the chart and graph as required.Originally Posted by [email protected]
Ed M
2004 Vette Coupe, LS2, MN6, Vararam, ARH/CATs, Ti's, 4:10, Trickflow 215, 30# SVO, Vette Doctors Cam, Fast 90/90, DD McLeod, DTE Brace, Hurst shifter, Bilsteins etc. 480/430
ERM Performance Tuning -- Interactive Learning ..from tuning software training to custom tunes
HP Tuners Dealer- VCM Suite (free 2hr training session with purchase), credits and new Version 2.0 turtorial available
http://www.ermperformancetuning.com
http://www.facebook.com/ERMPerformanceTuning
[email protected]
No "advance" is needed. This has worked just fine for months. You might have to setup a histogram instead of using a built in / included one that comes setup for you, but that is simple enough to do. And it's a whole heck of a lot faster to do compared to 2.24
Yes you need inj PW and engine RPM for it to work
Post a log and tune if you want help
VCM Suite V3+ GETTING STARTED THREADS / HOW TO's
Tuner by night
CPX Tuning
2005 Corvette, M6
ECS 1500 Supercharger
AlkyControl Meth, Monster LT1-S Twin, NT05R's
ID1000's, 220/240, .598/.598, 118 from Cam Motion
2007 Escalade, A6
Stock
For whatever reason, the default config is now RPM vs. MAP instead of RPM vs. airmass for the histograms (or whatever they're called now). So after changing the axis PID/sensor to airmass, you then have to go into the tune file and copy the spark axis labels for the airmass and paste them into the histogram unit values field in the histogram setup...
Not sure why they were changed from airmass to MAP - maybe newer cars are setup that way for their spark advance tables?
There are multiple defaults built in, under the Layouts menu.
We got this guy Not Sure, ...
I am still having issues with the latest version (tested tonight) reading alcohol %. It appears it is now called ethanol % but it is grey and goes away when you start scanning. I had no issues with the latest version and have to keep switching back and forth between versions now.
Davids3.0.Layout.Layout.xmlDavids3.0.Layout.Layout.xmlafr error custom.MathParameter.xml16-02-14 21-26-11.hpl
I tried to upload the log and layout from my 3.0 I am having a hard time getting the correct AFR %error. It does not reflect what the WB and Command AFR are.
Also no matter what I do with the graph layout, I cannot get it to populate the %AFR, I just downloaded the most recent update last night. .22 I believe.
this is becoming very frustrating, Hope someone can see were I configured it incorrectly. I tried all kinds of changes to the graphs with no avail.