Customer asked for a simulated long duration cam idle. He liked it!
http://www.youtube.com/watch?v=O45Nn...ature=youtu.be
Customer asked for a simulated long duration cam idle. He liked it!
http://www.youtube.com/watch?v=O45Nn...ature=youtu.be
Haha that sounds pretty good. What exactly have you changed? I've been playing around with mine,but I havnt had results as good as that.
RAMJET GHOST CAM LOPE TUNE
1, Goto Engine, Spark, Advance, Idle Adaptive Spark Control, Overspeed & Underspeed, P/N, Gear, & Coastdown. Enter ½ of highest RPM error constant value in first cell from 0. Interpolate from first entry to first constant value. Repeat for remaining tables.
2. Goto Engine, Idle, RPM, Adaptive Idle Proportional Enable RPM Error.
Subtract 10 from factory value.
3. Goto idle Integral Enable RPM Error. Enter value 5 less than new Proportional value.
4. Goto Proportional Airflow table. Multiply Normal values x 1.03.
5. Goto Integral Airflow table. Multiply Normal values x 1.20.
6. Goto Target Idle Speed table. Add 50 RPM to temperature stabilized idle speed cells. Copy same speeds into P/N cells.
Cool sound but how's the surge at a stop light?
Gray Ghost- The abomination. 2007 Chevrolet Silverado CCSB. 98mm turbo, nitrous, 428LSX, Rossler 80E with a brake. Finally finished. 23 psi, no numbers, Slow as hell.
PBM G8- Aluminum 364, twin Precision 67/66 turbos, 6L90 trans swap, CTS-V/Vaporworx fuel system, slowly making progress.
Dads 2011 CTS-V- Stock bottom end, stock heads, LS9 cam, pullies, ported blower, ported TB, D3 goodies, and lots of nitrous.
618/618 motor
906/862 spray
Caterpillar 50 Forklift- Duramax swap
Not bad at the stop lights. It does shake a bit - enough to rock the car.
This is a stock cam??
Email Tunes, [email protected]
96 TA Blown/Stroked, 4L80E/Fab 9
15 C7 A8 H/C 2.3 Blower/PI
14 Gen 5 Viper
Custom Mid Engine chassis, AKA GalBen C
Gray Ghost- The abomination. 2007 Chevrolet Silverado CCSB. 98mm turbo, nitrous, 428LSX, Rossler 80E with a brake. Finally finished. 23 psi, no numbers, Slow as hell.
PBM G8- Aluminum 364, twin Precision 67/66 turbos, 6L90 trans swap, CTS-V/Vaporworx fuel system, slowly making progress.
Dads 2011 CTS-V- Stock bottom end, stock heads, LS9 cam, pullies, ported blower, ported TB, D3 goodies, and lots of nitrous.
618/618 motor
906/862 spray
Caterpillar 50 Forklift- Duramax swap
Hmmm pretty cool
I have played with the overspeed underspeed timing tables before to add in or subtract A LOT of timing below 75 rpm swings to do something similiar, but never on a stock cam.
Problem is driveability usually suffers
Last edited by Ben Charles; 02-07-2013 at 04:31 PM.
Email Tunes, [email protected]
96 TA Blown/Stroked, 4L80E/Fab 9
15 C7 A8 H/C 2.3 Blower/PI
14 Gen 5 Viper
Custom Mid Engine chassis, AKA GalBen C
No driveability issues! Any throttle application removes the timing swings.
How're you getting around that? Every now and then with a car that has a pretty aggressive spark correction setup has an issue.
For instance, leaving a stop sign. Depending on where the spark control is at whenever you touch the gas, sometimes the car may leave at 18 degrees advance with the feeling of clean crisp throttle response. Other times it may leave at 6 degrees advance with the feeling of sluggish throttle response as it takes the ECM a bit to advance the timing back to cruise levels. Any help for that issue?
Gray Ghost- The abomination. 2007 Chevrolet Silverado CCSB. 98mm turbo, nitrous, 428LSX, Rossler 80E with a brake. Finally finished. 23 psi, no numbers, Slow as hell.
PBM G8- Aluminum 364, twin Precision 67/66 turbos, 6L90 trans swap, CTS-V/Vaporworx fuel system, slowly making progress.
Dads 2011 CTS-V- Stock bottom end, stock heads, LS9 cam, pullies, ported blower, ported TB, D3 goodies, and lots of nitrous.
618/618 motor
906/862 spray
Caterpillar 50 Forklift- Duramax swap
I like to limit Throttle Area Rate Increase to 50% in gear 1 low RPM area. This also aids traction on A6 cars with that deep 1st gear.
can this be done to a ls1?
67 camaro 6.0lq4 turbo build in process
89 mustang coupe ls1 80mmturbo, holley dominator efi on e85
02 lexus is300 lq4, cam,headers,fast 92 intake
and no there isnt anything in my yard unmodified
I would like to try this.
Can you explain #1 a little more clearly please?
For 4 and 5, I have several tables, adjust all of them?
1, Goto Engine, Spark, Advance, Idle Adaptive Spark Control, Overspeed & Underspeed, P/N, Gear, & Coastdown. Enter ½ of highest RPM error constant value in first cell from 0. Interpolate from first entry to first constant value. Repeat for remaining tables.
2. Goto Engine, Idle, RPM, Adaptive Idle Proportional Enable RPM Error.
Subtract 10 from factory value.
3. Goto idle Integral Enable RPM Error. Enter value 5 less than new Proportional value.
4. Goto Proportional Airflow table. Multiply Normal values x 1.03.
5. Goto Integral Airflow table. Multiply Normal values x 1.20.
6. Goto Target Idle Speed table. Add 50 RPM to temperature stabilized idle speed cells. Copy same speeds into P/N cells.
Mr. Ramjet?
id like to try this as well but not really following along with #1, 4 and 5 as well, there are several tables. maybe the tables are different for a ls f-body?
Last edited by hodge9386; 03-29-2013 at 12:21 PM.
could you make a suggestion as to which tables should me modified if any?
Step 4..... Multiply Normal values x 1.03 is that only positive values or both the negative and positive in those tables etc.
2017 Toyota Kluger - 10.1" Android Custom Head Unit, Rockford Fosgate Speakers, 85kg Roof Racks. Prev: 2009 Cammed VE SS Sedan, DOD Delete, 210/218 550', RAMJet OTR, HiFlowCats, IQ System, Amp/Speakers.
Sorry to resurrect a dead posting, but I just came across this and think this would be pretty neat to mess with my friends. But as everyone was saying, can you clear up step one a little please?
Does anyone know how to get a hold of roger ramjet?