Hey all
Have a 2014 V6 pentastar in an old dodge colt (standalone) trying to eliminate skims. Using MPVI I can read file and make changes but I encounter a write fail when trying to reload the file?...
Type: Posts; User: 53mercury
Hey all
Have a 2014 V6 pentastar in an old dodge colt (standalone) trying to eliminate skims. Using MPVI I can read file and make changes but I encounter a write fail when trying to reload the file?...
Hello folks
Been messin with this swapped Viper powerplant (Gen4 2008 in a Roadrunner) that is standalone using all the components from the Viper. Tuned with HP Tuners but can?t seem to get it from...
Hi all
Put A 2008 Gen 4 Viper in A 1971 Roadrunner I've modified the viper engine 'bay' harness to operate standalone and using everything from the viper only modification is to the exhaust 'past...
Anyone out there swapping gen 4?s ever try using the neutral safety relay? Pin 52 of the J1 yellow/black seems to send a ground signal to the start relay (allowing starter control for park/neutral)...
Hmmm I'm having the same issue! went from a 2008 truck (e38 pcm) to a 2012 corvette pcm (e38) :so tap shift could be used:. the problem is I plug in the old pcm, test the fans via scanner function...
Where and how or who do we send the 2011-14 ford pcm for PATS delete? Do we address it to Eric and send it or? Never had to send one out before and not sure how? Any info would be appreciated.
Probably been asked before...
2012 ford pickup (5.0) can the pats be disabled via HP Tuners? It?s set up in a ?stand alone? application . If not what steps (systems) are guys using to eliminate...
I know ...it makes no sense! How is it that HP Tuners allows adjustment of the rear speed sensor and not the front? Just about everything has ABS and the computer will only allow 5% difference. Be...
alright all you tuners out there got a speedo problem just like it seems everyone else does on here that change tire size and in researching all of it I still see no real fix? Case in point 08...
63140
Yeah I did actually and it still only modifies the PPM table which for some reason only changes the rear speed sensor calibration! I'm not sure if tire size can only go up (physically bigger) in hp...
Hey guys got a 2008 Silverado 4x4 (doner truck) condensed into a 1953 Chevy. Running all the stock modules including trans controller, ebcm and stock cluster. All tires are the same size and the gear...
Excellent news it looks deadly!!! I'm not as far along as you are. all good so far except oil pan will need some mods to clear steering rack .. I'll certianly keep you posted.542805428154282
What is it your looking to do?
I've been beating on a 3valve for years now ... added a supercharger, then nitrous, custom headers, and on the list goes. It's only now with race gas and a fairly big...
I'll will help for sure 2012 ram 5.7 in a 70 duster (standalone) still no start (skim disable) NGC4 I believe
Hey UR50SLO good to hear you have it working I have not started the wiring on this project yet myself (fitting the engine etc) is there anything out of the ordinary I should be aware of? When I...
That's great I'm not looking to change calibration over stock (not yet anyways ) get it running first. All I need now is schematics for this beast and it's done.
Thanks a lot Keith really...
Excellent! Hey Keith is there any un-knowns I should be aware of? VATS disable should be same as chevy I'm guessing I have done many LS transplants along with a couple fords with good success this...
Anyone doing a transplant of this viper engine (as I did 2008 viper gen 4 in 71 roadrunner) use the stock pcm? Not really any info anywhere if this is possible or not! I'm thinking (hoping) that it'd...
what year esclade? If it ain't 08 and newer you may have wrong crank trigger 28 vs 58
Checked wiring of the can bus on the weekend.......all wired correctly so I tried putting a 120 ohm esister after the BCM....still no change!!! I just don't get it.
Great info I'm gonna cheak the can routing and see if I have maybe made a mistake on which module goes where in the system.
Thanks
Awesome I think I may have made a mistake here ! So I understand the GMLAN schematic and I'm assuming it's terminated inside the ECM with a 120 ohm resistor but I do not see a 120 at the datalink I'm...
Still baffeled by this! Was in contact with John at speartech again and he says that he may have a different OS that "MIGHT" work..... but I don't want to take the chance and loose the info "file" I...
I also transplanted a LY6 from a 08 2500HD and had issues with the vette fuel pedal! I ditched the vette pedal ran the truck pedal and problem solved. May not work for you with psi harness but if you...