Page 12 of 220 FirstFirst ... 289101112131415162262112 ... LastLast
Threads 221 to 240 of 4385

Forum: GM L4, I5, I6 Tuning - Engine

  1. Sticky Thread Sticky: General 4, 5 & I6 Cylinder How-To's & Tuning Info

    Started by Shifted, 04-16-2006
    2 Pages •
    1 2
    2 Attachment(s)
    • Replies: 30
    • Views: 119,261
    Dannye
    03-23-2024 Go to last post

  1. Trying to figure this I6 2006 Envoy.

    Started by Sierravgen, 10-18-2022
    5 Attachment(s)
    • Replies: 14
    • Views: 1,877
    SiriusC1024
    11-18-2022 Go to last post

  2. E39A, LHU engine

    Started by kw8, 12-21-2021
    4 Attachment(s)
    • Replies: 11
    • Views: 3,353
    gopropov
    11-06-2022 Go to last post

  3. LNF Standalone

    Started by hefe33, 11-05-2022
    • Replies: 2
    • Views: 959
    gtstorey
    11-06-2022 Go to last post

  4. Need some advice on too much low end boost after factory turbo replacement.

    Started by Jmaurer, 10-14-2022
    2 Pages •
    1 2
    9 Attachment(s)
    • Replies: 21
    • Views: 2,856
    cobaltssoverbooster
    10-30-2022 Go to last post

  5. P11 PCM traction control question.

    Started by Lunatic, 10-27-2022
    1 Attachment(s)
    • Replies: 2
    • Views: 728
    Lunatic
    10-27-2022 Go to last post

  6. OBD II Readines Monitor "trick"?

    Started by Gremlin85, 07-28-2011
    3 Pages •
    1 2 3
    • Replies: 45
    • Views: 106,601
    ZeroBoostBuick
    10-26-2022 Go to last post

  7. 300-400hp Ecotec timing on pump gas??

    Started by GrannySShifting, 10-06-2022
    3 Attachment(s)
    • Replies: 9
    • Views: 1,828
    ZeroBoostBuick
    10-26-2022 Go to last post

  8. Boosted 98 Cavalier LN2

    Started by wagonwes, 02-17-2010
    2 Pages •
    1 2
    • Replies: 23
    • Views: 12,707
    JohnSi
    10-16-2022 Go to last post

  9. 2/3 bar map support?

    Started by Jayson, 03-01-2006
    3 Pages •
    1 2 3
    1 Attachment(s)
    • Replies: 45
    • Views: 17,763
    JohnSi
    10-16-2022 Go to last post

  10. NA Solstice gone turbo, chasing odd misfire counts on cyl4 but no obvious reason??

    Started by GrannySShifting, 09-30-2022
    3 Attachment(s)
    • Replies: 13
    • Views: 1,644
    GrannySShifting
    10-14-2022 Go to last post

  11. Anyone have WOT datalog on turbo Ecotec LNF stage II kit?

    Started by GrannySShifting, 10-13-2022
    • Replies: 0
    • Views: 473
    GrannySShifting
    10-13-2022 Go to last post

  12. E67 Ecotec, can you do flex like V8 E67s?

    Started by GrannySShifting, 10-06-2022
    • Replies: 2
    • Views: 716
    GrannySShifting
    10-13-2022 Go to last post

  13. Flex Fuel and the e67 ECM on an LE5

    Started by Robotech, 03-07-2019
    • Replies: 6
    • Views: 3,904
    GrannySShifting
    10-06-2022 Go to last post

  14. 3.5" intake LCV engine

    Started by Mr.AT, 10-05-2022
    • Replies: 4
    • Views: 728
    Mr.AT
    10-05-2022 Go to last post

  15. Ats 2.5 2014

    Started by Mr.AT, 09-28-2022
    • Replies: 0
    • Views: 601
    Mr.AT
    09-28-2022 Go to last post

  16. Gm 1.4 luj sandrail rev limiter help

    Started by Bearr2684, 05-23-2022
    3 Attachment(s)
    • Replies: 9
    • Views: 1,984
    Ostercrawler
    09-27-2022 Go to last post

  17. Question whats the proper drive cycle procedure ?

    Started by fst100, 09-19-2022
    • Replies: 0
    • Views: 623
    fst100
    09-19-2022 Go to last post

  18. 2016 E80 ECM E85 Sensor

    Started by scottyl, 01-25-2020
    • Replies: 15
    • Views: 6,177
    [email protected]
    09-10-2022 Go to last post

  19. Tuning 2.2 Ecotec with Cavalier ECM

    Started by cstew00, 08-13-2018
    2 Attachment(s)
    • Replies: 4
    • Views: 12,549
    Johnwayne
    09-07-2022 Go to last post

  20. RPM-Motorsports LE5 Turbo Install Idle Issues, Running Lean,

    Started by Engnineere, 09-20-2021
    2 Pages •
    1 2
    13 Attachment(s)
    • Replies: 20
    • Views: 6,905
    Engnineere
    09-07-2022 Go to last post
Page 12 of 220 FirstFirst ... 289101112131415162262112 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.