Page 1062 of 1243 FirstFirst ... 6256296210121052105810591060106110621063106410651066107211121162 ... LastLast
Threads 21221 to 21240 of 24842

Forum: GM V8 Tuning - Engine, Gas (Gen 3)

(1997-2009, LS1, LS6, ...)

  1. Sticky Thread Sticky: If you want us to help with a tune or scan issue post your .hpt file, log & .cfg too.

    Started by jimmyblue, 10-19-2009
    92 Attachment(s)
    • Replies: 0
    • Views: 108,705
    jimmyblue
    10-19-2009 Go to last post

  2. Sticky Thread Sticky: READ ME!!! General tuning info and how-to's

    Started by WS6FirebirdTA00, 02-07-2006
    • Replies: 0
    • Views: 292,880
    WS6FirebirdTA00
    02-07-2006 Go to last post

  1. Low Timing due to IAT Modifier table

    Started by Bill Hooper, 07-21-2007
    • Replies: 9
    • Views: 5,539
    PBMFIsMe
    07-23-2007 Go to last post

  2. How often should misfires happen?

    Started by Mike04, 07-16-2007
    • Replies: 4
    • Views: 2,336
    Mike04
    07-23-2007 Go to last post

  3. Loosing timing?

    Started by Rob's 73, 07-23-2007
    • Replies: 1
    • Views: 1,559
    Bill@HPTuners
    07-23-2007 Go to last post

  4. Stumble at idle for about 60 seconds after initial start up

    Started by TriPinTaZ, 07-16-2007
    • Replies: 13
    • Views: 5,599
    TriPinTaZ
    07-23-2007 Go to last post

  5. Weird non PCM codes after flashing

    Started by zo6racerx, 07-22-2007
    • Replies: 3
    • Views: 1,944
    EC_Tune
    07-23-2007 Go to last post

  6. Switching MAF's question?

    Started by 01WS6, 07-22-2007
    • Replies: 1
    • Views: 1,620
    EC_Tune
    07-23-2007 Go to last post

  7. VE Tuning and the 5 pin MAF Sensor

    Started by TFS_Z06, 07-17-2007
    • Replies: 5
    • Views: 2,661
    EC_Tune
    07-23-2007 Go to last post

  8. What exactly are IAC counts?

    Started by 7420NW7TH, 07-22-2007
    • Replies: 1
    • Views: 1,751
    Hauss
    07-22-2007 Go to last post

  9. Idle hang on startup

    Started by 01WS6, 07-21-2007
    • Replies: 4
    • Views: 2,635
    01WS6
    07-22-2007 Go to last post

  10. 2Bar SD tune AFR problems

    Started by tut5079, 07-20-2007
    • Replies: 4
    • Views: 2,602
    tut5079
    07-21-2007 Go to last post

  11. Need help with diagnosis of part throttle problem

    Started by vetteman3, 07-19-2007
    • Replies: 7
    • Views: 2,962
    Billf6531
    07-21-2007 Go to last post

  12. VE & MAF good FT not.

    Started by domestic rice, 07-19-2007
    • Replies: 3
    • Views: 2,036
    Confused1
    07-21-2007 Go to last post

  13. A New PCM

    Started by INTHERED, 07-12-2007
    • Replies: 8
    • Views: 3,791
    SSUte01
    07-20-2007 Go to last post

  14. Fuel milage getting worse????Y???

    Started by firefly9r68, 07-08-2007
    • Replies: 5
    • Views: 2,650
    firefly9r68
    07-20-2007 Go to last post

  15. Thumbs down Is That right?

    Started by The devil, 06-01-2007
    • Replies: 11
    • Views: 3,722
    The devil
    07-19-2007 Go to last post

  16. Question about Mustang Dyno's

    Started by zo6racerx, 07-19-2007
    • Replies: 0
    • Views: 1,776
    zo6racerx
    07-19-2007 Go to last post

  17. GM Flex Fuel Software Update

    Started by seven ends, 07-11-2007
    • Replies: 16
    • Views: 7,436
    Bill@HPTuners
    07-19-2007 Go to last post

  18. How to upgrade O/S?

    Started by forrestd, 07-18-2007
    • Replies: 5
    • Views: 2,438
    Bill@HPTuners
    07-19-2007 Go to last post

  19. Huge idle problem...

    Started by mulot30th, 07-11-2007
    2 Pages •
    1 2
    • Replies: 27
    • Views: 11,424
    mulot30th
    07-19-2007 Go to last post

  20. Backfiring During shift on 05's Cammed 5.3 / 6.0

    Started by niceguy, 07-18-2007
    • Replies: 8
    • Views: 3,379
    bullygoat
    07-19-2007 Go to last post
Page 1062 of 1243 FirstFirst ... 6256296210121052105810591060106110621063106410651066107211121162 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.