On a 2006 Corvette with a eforce supercharger with the tune that came with the eforce kit, is it possible to read that tune and modify it with HP tuners?
On a 2006 Corvette with a eforce supercharger with the tune that came with the eforce kit, is it possible to read that tune and modify it with HP tuners?
NotoriouSS TAD
DATLS7N 73' Datsun 620 LS7/HNC/TR6060/4.10/T2/2450lbs/603RWHP
J5 - 96' Impala SS - 4700lb autocross machine
Langston - 96' Caprice 9C1 Beater
Rosie - 67' El Co - race truck w/ plates
Wall-E - 21' Tesla Model 3P
2004 Vette Coupe, LS2, MN6, Vararam, ARH/CATs, Ti's, 4:10, Trickflow 215, 30# SVO, Vette Doctors Cam, Fast 90/90, DD McLeod, DTE Brace, Hurst shifter, Bilsteins etc. 480/430
ERM Performance Tuning -- Interactive Learning ..from tuning software training to custom tunes
HP Tuners Dealer- VCM Suite (free 2hr training session with purchase), credits and new Version 2.0 turtorial available
http://www.ermperformancetuning.com
http://www.facebook.com/ERMPerformanceTuning
[email protected]
Weird. The last E-Force car I did wouldn't open because of a checksum error. I had to overwrite with a stock file.
DSX Tuning - Authorized HP Tuners Dealer
http://www.dsxtuning.com
http://www.facebook.com/dsx.tuning
Just say no to bull s***.
IF YOU WANT HELP, POST A FILE!
just did it yesterday with a 2012. Once I finally got a file from edelbrock for the SCT which did not say ECU unknown it worked.
Janky Monkey Tuning
Call or PM for tuning solutions.
Cell 210-954-4985
Wrench turning provided by 2 Tightwads Racing.
Tune your own? Start here ----> Open Editor ---> Hit F1...READ!
READ SOME MORE (Thank username 69Lt1bird): http://ls1tuningguide.com/
Still lost? Consult a Pro!
www.thetuningschool.com
www.calibratedsuccess.com
www.tunedbyfrost.com
actually I have seen much worse tunes..............the latter ones are not as bad as the older ones where cars would not even idle..........
here it is, 2012 Cammy LS3 580hp kit
I get a fail to load error when trying to open that file, I guess I need the latest beta maybe?
I currently have 2.23.433
2010 GXP Maloo ute, LS3, 6L80E.
MM heads, 240/252@50 solid cam, 12.75:1 compression, 4500 Dominator converter, 3.46 rears.
Shooting for 10s eventually.
yes latest beta, this is a 2012 model car........
hi guys
would you be willing to share the file, lost in the sauce trying to tune on my own
no clue where to go
at least that "2012 Cammy LS3 580hp kit" file has the correct Cylinder Charge Temp values for an IAT sensor located inside the intake manifold... similar to a ZR1 or ZL1. Is the Eforce IAT inside the manifold like the rest of these top mount blowers?
My Whipple tune used stock values which are setup for an IAT sensor 2-3 feet away, in the MAF sensor, next to the air cleaner. I changed them, but didnt see a big difference. But still.
Speaking of IAT's, how are the Edlebrock IAT readings? My whipple IAT's were consistently 15F low compared to coolant temp and ambient air temp on radio after letting the car sit in my garage for 2-3 days.... at 75F, 40F, etc.. Always 15F low, and not starting it. So while driving normally IAT's would read only 15F above ambient air temp... when actually it's 30F over ambient.
2010 Camaro LS3 (E38 ECU - Spark only). MS3X running complete RTT fuel control (wideband).
Whipple 2.9L, 3.875" Pulley, kit injectors, supplied MSD Boost-A-Pump, stock pump
LG Motorsports 1 7/8" Headers - No Cats, stock mid pipe with JBA Axle Back
ZL1 Wheels/Tires
here is the tune from 2007 auto vette not sure if its original tune i bought the car with e-force installed. Car is stock except borla exhaust i think
2018 mustang gt a10 with headers and e85
Late back to the party, but not as bad as I had previously seen. Still pretty rich PE and MAF only. But like you said, have seen worse. They all can use a bit of massaging but they have to be on the very safe side for sure. We don't ever use them though. Start with a stock file and build a new one including VE.
Ed M
Last edited by mowton; 12-02-2012 at 06:28 AM.
2004 Vette Coupe, LS2, MN6, Vararam, ARH/CATs, Ti's, 4:10, Trickflow 215, 30# SVO, Vette Doctors Cam, Fast 90/90, DD McLeod, DTE Brace, Hurst shifter, Bilsteins etc. 480/430
ERM Performance Tuning -- Interactive Learning ..from tuning software training to custom tunes
HP Tuners Dealer- VCM Suite (free 2hr training session with purchase), credits and new Version 2.0 turtorial available
http://www.ermperformancetuning.com
http://www.facebook.com/ERMPerformanceTuning
[email protected]
I also have a 2008 corvette c6 with the edelbrock supercharger kit. Did the install myself, don't trust just any ase certified mechanic. It came with the sct 3416e2 handheld programmer. I wanted to make some changes to the tune, called sct it is tuner locked. But interestingly they said that the tune does an engine mod for the supercharger, the transmission Tcm is untouched. I guess that's why it shifts way to soon for me. I wanted to access some of those parameters and there is also a flat spot with 20% throttle between low speed shifts. Anyone have some similar issues. I'm a mechanic with 30yrs experience fixing lots of cars and with pretty good experience working on c5 and c6 vettes. Has anyone gotten a tune with a tuning shop that you could give me for a starting point, and later mod to what I need. Thx for reading.
I installed the 599 hp kit on my 08 C6 M6 coupe & HP Tuners read it fine & I'm able to make changes as needed also.
EFI specialist
Advanced diagnostics, tuning, emissions
HPtuners dealer and tech support
email=[email protected]
I'm running 08 C6 A6 Eforce 599 Kit, the stock Edelbrock tune is rich, there is a lot to be gained from HP uners, also if you have an A6 then modifying the transmission will help immensely.
PM me if you want a copy of my tune (before I put in the ZR1 cam) for comparison
2008 Corvette C6 A6
E force 599HP kit, 3.25 pulley
ZR1 Cam, ATI Balancer
160 stat, Dewitts Radiator
LG 1 7/8 Superpros, delete cats, xpipe
Century Built 6l80e, Ext. Transmission Cooler
3200 Yank
2.73 rear
Does anyone have a copy of the LS2 E-force tune in an M6 C6?