Have you tried checking out romraider? I think there's support for ms42 and it's free I used it for my e36 328 and a m3 works well
Have you tried checking out romraider? I think there's support for ms42 and it's free I used it for my e36 328 and a m3 works well
rtt still has issues with loading. says failed when trying to pull the ve table. then it adds 40% to the entire "shown" ve table. ::shrugs:: back to 2.24 for rtt...
The most hated, make the most power.
93 Ranger. 5.3 D1X. 1069hp.
I just downloaded 3.4 and now my interface doesn't show any of the vehicles that are on the cable. Any help would be appreciated.
Run an info log and see if that syncs them up
As far as the newer versions opening the older files. I have some saved files I use on swapped vehicles that will not open in the newer versions. The latest version they will open with is 2.24
Michael Bray
Rusty Knuckle Garage
Slidell, Louisiana
20yr Master Tech.
Advanced Level Specialist
Custom Car Fabrication, Customization, High Performance.
GM World Class Technician
Shop Owner
Does this update do a firmware update that breaks 2.24 compatibility?
9 sec Montecarlo SS
It's cost/profit.
Getting into any module is usually pretty difficult.
We got this guy Not Sure, ...
]06 Ram 1500 545RFE transmission support? Jtec?[ Any time I ask anything about either, all I get for a reply is; It's not currently supported, no ETA. I would just like to know if these things are planned to be supported, or not. I understand there was a lot of R&D time with 2017 models and Benze support. Respectfully, an answer other than the broken record of Not Supported, No ETA, is awaited. Thank you
The reason you get those answers is because those are the answers we can give.
No ETA.
We got this guy Not Sure, ...
I prefer to run Window 7 with a "Medium 125%" display size. See Control Panel -> All Control Panel Items -> display.
Starting with 3.2 and now unfortunately also in 3.4 Editor, the bottom few pixels in each table row are truncated, making it hard to read.
Guess I should have reported that earlier.
Some of us just noticed this recently, but you can't select individual cells - such as in a MAF hz data log - and then copy paste into the editor unless you select large strains of cells... Can this be fixed please...
2010 Vette Stock Bottom LS3 - LS2 APS Twin Turbo Kit, Trick Flow Heads and Custom Cam - 12psi - 714rwhp and 820rwtq / 100hp Nitrous Shot starting at 3000 rpms - 948rwhp and 1044rwtq still on 93
2011 Vette Cam Only Internal Mod in stock LS3 -- YSI @ 18psi - 811rwhp on 93 / 926rwhp on E60 & 1008rwhp with a 50 shot of nitrous all through a 6L80
~Greg Huggins~
Remote Tuning Available at gh[email protected]
Mobile Tuning Available for North Georgia and WNC
I just updated to 3.4 and now it tells me the interface is not found or not responding, and I have run an info log and that did nothing to help.
Was hoping 3.4 would enable the scan feature to be used across all obdII compliant vehicles. Tested it out on some that the old version was not able to recognize and still same thing.
Post a log and tune if you want help
VCM Suite V3+ GETTING STARTED THREADS / HOW TO's
Tuner by night
CPX Tuning
2005 Corvette, M6
ECS 1500 Supercharger
AlkyControl Meth, Monster LT1-S Twin, NT05R's
ID1000's, 220/240, .598/.598, 118 from Cam Motion
2007 Escalade, A6
Stock