A saved layout includes graphs/charts/gauges all within the one layout file that you saved
Another thing I noticed,
AFR error is no longer supported on the channels
Can't add math parameters to the channel list on V3
AFR error is a math pid. It's "virtual" to the application, meaning it's not bound to any particular input, thus, it doesn't go into the channels display.
Channels display are for inputs that are directly bound to some source.
We got this guy Not Sure, ...
working on a p59 pcm, have latest 3.0. looking for MAF Sensor Fail Frequency to work on LTFT (i am a novice tuner) on my personal vehicle. I can't find it at all. any help?
Please post the tune and I'll take a look
We have two MPVI's in our shop and I am using a different laptop for each one. I see (attached) where the software can now remember multiple application keys and interface license information. Does that mean I can use both MPVI's on one laptop? If so I am going to need someone to walk me through how to do it because when I try it the software doesn't recognize the application key's.
Yes, you can now use multiple MPVI's on one laptop.
If it's not recognizing your application key, you're copy/pasting it wrong.
If you enter the application key, and it gets added to the list, it's recognized.
We got this guy Not Sure, ...
Thanks I will do that. I was going to do it but didn't want to confuse the software with two interfaces. On a side note: I have spent many hours learning the new 3.0 software with some frustration at times. I am now finally starting to understand how everything works. Normally it's the little stupid things that kick's my butt. You have a good reliable product that gives me great confidant in using it. Thanks
I audited all of the parameters in my old 2.24 config files. I cannot locate the following parameters in build 3.0.27 by searching for parts of their name, which are recognized in 2.24.1172, OS 9375576:
Idle AC Airflow
Idle Adapt (STIT)
Idle advance
Idle base Gear Airflow
Idle base PN Airflow
Idle cracker Airflow
Idle fans Airflow
Idle Follower Airflow
Idle park position Airflow
Idle startup Airflow
Ignition voltage
LTIT Gear/ACoff
LTIT PN/ACoff
tcc slip %
torque mgmt advance
trans turbine RPM
When I add these parameters to a 2.24.1172 config and start logging, none are shown as '<unsupported>'.
I see its still going on here.
I need to ask if build 2.24.75 will run beside 3.0?
I have a truck on 2.24.75 and jut took ownership of a 2013 Charger R/T and would like to run 3.0 on it to get used to it before possibly migrating the truck to 3.0?
The truck may never be tweaked again, I'm happy with it.
Did you ever provide a version that will run side by side?
2013 Dodge Charger R/T Plus, Stock 5.7L, Edelbrock E-Force Stage 1, 3.25" Pulley, 450-HP 459-TQ.
Corsa Sport CatBack, 3.06:1 Wavetrac, Dual Fans, 1-7/16 Radiator, Mopar Oil Cooler
2005 Radix'd Silverado L33 5.3 ECSB Z71 @ 387-HP 395-TQ
Hey I'm sure it's been asked a million times. But I can't seem to figure out why my 2.24 licensed vehicles all show as unlicensed in 3.0. Application key is correct and shows the vehicle in the list but still can't write the files.
in the scanner Is there any reason (im trying to learn the new software) that afr error and other thing only come up as one bar when the map is set for 2bar and why the two bar only goes to 160 kpa
thanks
Jim
maybe someone could post one so I could see what im doing wrong
Last edited by usc45cal; 02-20-2016 at 01:17 PM.
This is fixed in tomorrows 3.0.
97/98 GM LS1 vehicles do not report an OS ID, unless you're running one of our custom operating systems. We require the OS id to determine what OS specific parmaeters are supported. For these vehicles though, we just assume you have an updated OS from GM. This is what we did in 2.24, and what we have implemented in 3.0.
It will work for most 97/98 LS1 vehicles (just like 2.24), but will likely show invalid data if your operating system isn't updated (exactly like 2.24 would have done).
We got this guy Not Sure, ...