Search:

Type: Posts; User: popeye55

Page 1 of 9 1 2 3 4

Search: Search took 0.00 seconds.

  1. Anyone got any thoughts?

    Anyone got any thoughts?
  2. Ecotec 2.2 TCC and shift point theorys, need a little help

    I am trying to figure out the best shift theory on setting up my shift points and converter lock up for mileage.

    My goal is mileage and not power...not that we had much power to start with! lol
    ...
  3. Replies
    44
    Views
    20,717

    See if this shows up

    See if this shows up
  4. Replies
    44
    Views
    20,717

    I saved the screen shots to word and I will be...

    I saved the screen shots to word and I will be danged if I can get them to upload. Its been uphill all day.
  5. Replies
    44
    Views
    20,717

    So I reconnected the PCM, then re connected the...

    So I reconnected the PCM, then re connected the battery and left on trickle charge. I followed GM's procedure for the security system relearn. Car still would only crank over but not start. I pulled...
  6. Replies
    44
    Views
    20,717

    Im trying to do a relearn on the secutity system....

    Im trying to do a relearn on the secutity system. I don't hear the fuel pump prime and I am getting a Error on the cluster where the odometer would be.
  7. Replies
    44
    Views
    20,717

    ok, I will try full write

    ok, I will try full write
  8. Replies
    44
    Views
    20,717

    Im going to go back out. Reconnect the PCM,...

    Im going to go back out. Reconnect the PCM, Reconnect the battery, remove radio fuse and try a write calibration
    and see what happen
  9. Replies
    44
    Views
    20,717

    Yes the car ran to where I stopped. It wrote in...

    Yes the car ran to where I stopped. It wrote in low speed and appeared to be a slow but good flash. However it would just crank and not fire. I then was unable to get the scanner to connect and read...
  10. Replies
    44
    Views
    20,717

    These were not my shops. I got off work...

    These were not my shops. I got off work "Firefighter" and drove to a local store and had about 20 min of logging from the drive. At the store I made a few VE table changes and went flash. Pulled the...
  11. Replies
    44
    Views
    20,717

    That's funny but not funny because had the...

    That's funny but not funny because had the HPtuners shops they always full write.... no maybe they meant with what they tune and that not being my car model. Is there anything else Bill to try,...
  12. Replies
    44
    Views
    20,717

    So had the car towed back 100miles. Got it in...

    So had the car towed back 100miles. Got it in the shop, disconnected the battery and letting it charge, also unplugged the PCM for the time being. Not sure either will make a difference but I seen...
  13. Replies
    44
    Views
    20,717

    I am not sure how to post a screen shot but I...

    I am not sure how to post a screen shot but I followed your instructions Motown and there was nothing in the remote tuner box to clear or Slave data
  14. Replies
    44
    Views
    20,717

    I posted the tune. Here is the Suit info ...

    I posted the tune. Here is the Suit info

    *removed*
  15. Replies
    44
    Views
    20,717

    56887 I have tried a write caliberation, and...

    56887
    I have tried a write caliberation, and full write. I am running version 3.0.37
  16. Replies
    44
    Views
    20,717

    Help stuck along road

    Im stuck!!!! I go to flash a tune on a 2005 Cavalier and when I click write i get a fail that says Controller Unlocker/ Timed out.
    No wifi so I cant post anything. Any help? 4192034443
    Literally...
  17. Replies
    44
    Views
    20,717

    Anyone have anyone I might could call?

    Anyone have anyone I might could call?
  18. Replies
    44
    Views
    20,717

    Help stuck along road

    So I have a stock 2.2 2005 cavalier. I go to flash a tune after some VE adjustments. Now when I go to flash all I get is controller unlocker, timed out. Ive pulled fuse, unhooked battery etc etc. ...
  19. Replies
    3
    Views
    2,402

    Couple simple Scanner questions.

    Here you go,

    1. Can I create a filter and apply it to a log that's already been logged or does the filter need to be applied before I log date. Example on LTFT I want to only log with throttle...
  20. Replies
    3
    Views
    1,967

    Excellent I will have to give this a shot. Thanks...

    Excellent I will have to give this a shot. Thanks for the replies everyone.
  21. Replies
    3
    Views
    1,967

    Scanning non licensed cars/trucks

    I have the MVI pro cable and I am wanting to know if I can just connect to any OB2 and use the scanner functions? Is there a update or patch or anything? Its my understanding I can data log/scan...
  22. Tried that and im missing a lot of pids and zero...

    Tried that and im missing a lot of pids and zero trans pids. However if i pull a log from last week when using 2.24 all those pids were there and logging
  23. Yes.

    Yes.
  24. 3.0 Scanner downloaded now missing lots of parameters

    So I had been using the 2.24 version for scanning my 2005 2.2 Cavalier. I had configurations set up for trans tuning and VE tuning. I down load the new 3.0 and I go to make new scanner configurations...
  25. Replies
    10
    Views
    5,144

    I'll give that a try.

    I'll give that a try.
Results 1 to 25 of 203
Page 1 of 9 1 2 3 4