Thanks. I didn't tune this truck it had a blown motor when my buddy got it a 6.0 cracked ringlands. We swapped it with a junk yard 5.3, it had the shit rods with arp rod bolts. The plan was to run a...
Type: Posts; User: autoaddictions
Thanks. I didn't tune this truck it had a blown motor when my buddy got it a 6.0 cracked ringlands. We swapped it with a junk yard 5.3, it had the shit rods with arp rod bolts. The plan was to run a...
The back story= 04 Silverado S400 turbo with meth. 2 bar SD tune had 6.0 motor i got to aggressive on timing and cracked a ring land. New motor Stock 5.3 gen 3 Arp studs, Gapped rings, 862 heads...
Thank you The calculated Airmass was set to 4.10 however the Air flow was 105 and less. Due you think this could cause the issue. ??
03 Silverado Turbo 2 bar SD tune was good it ran fine. I sold the stock 6.0 for a forged 5.3 upon start up I got (reduced power ) engine dies. codes are P0106 and P1514. I haven't played with the...
Hellbents10 Can you post up a tune that u did this too so i can see what settings u used. Id like to try it. I have no maf sensor in the truck is one required for this trick..
Im using a ecu from a 2002 chevy blazer as well as the dash this way i have a working dash with a tach and speedo ect. the harness was re pinned for the extra 2 injectors. Then segment swap for the...
i will try this.. I have tried tons off combinations. The result is always the same. I don't understand why it will fail the maf and set the code every time if i let it sit for hours. But if i flash...
I have 3 bar SD tune in my LS swapped s10. The engine runs amazing I swapped the rear to a 3.08 and im trying to get the WOT shift points dialed in. it wont shift into 2nd at WOT. Ever time i make a...
I have a s10 with a 6.0 turbo 4l80 conversion. Im running a 3.08 rear 285/55/15 tire 27.9 tall. My car seems to shift ok at part throttle and the spedo is spot on. Can somebody look at my tune and...
Got it thanks !!
The need for using version 2.24 would not be necessary if somebody can tell me where to set the maf fail to 0 at in version 2.25. There is a tab for this in 2.24 under Engine Diag, airflow, MAF...
here is tune file and log of cold start and idle 55536 55537
I did read with 2.24 it successfully reads the tune then prompts me to save it. I name it XXXXXX.hpt. then when I open it in 2.24 it gives me this.
Invalid VIN/OS Pair VCM Flashing disabled
Im having issues with maf code setting for a 3bar SD tune. It takes 10 min of cranking before maf codes set, and ten it will start. I cannot use 2.24 since the tune was created in 2.25. there is a...
Well it worked 2 times!! I made some timing changes a 3rd time and it wouldn't start. Looked at the scanner and no maf codes. After 10 min of cranking on and off it started and the codes populated...
Man thanks a bunch. It worked like a champ. I cant thank you enough for taking the time to explain this in detail to me..
I don't believe you can. I created my tune in beta and I cannot read it with 2.24. You would think there backwards compatible but in my case it's doesn't seem so. Am I the only one. I get an error it...
yes 3 bar sd tune.
I needed a segment swap so I used beta. I think its the Maf not failing as well im not sure what to do about it. Is there a way to make it set the code instead of cranking the crap out of it.
55475
I have a 6.0 turbo swapped 1998 s10. Im running 02s10 blazer v6 pcm and cluster. This way everything in the dash works. 3 bar speed density tune. I have it running pretty good however when I flash a...
I have tried. It will not bring up icon for rtt. I have cheched to make sure its enabled in editor. Its a gen 3 motor segment swaped chevy 2002 s 10 blazer pcm.
Since my tune required segment swap my tune was created with 2.25. I have to use 2.24 Scanner since you cant add PID for wide band in Beta scanner.. Is there a way to use RTT in my situation. Why...
I don't see these tabs under airflow in 2.25beta can somebody set me strait. This this is a nightmare to start after a reflash.