Asked the question at SEMA. Firmware issue with the current MPVI Pro interface. No updates planned. Probably available in the next version of the MPVI Pro interface.
Type: Posts; User: wstaab
Asked the question at SEMA. Firmware issue with the current MPVI Pro interface. No updates planned. Probably available in the next version of the MPVI Pro interface.
Update from support: This is a known issue, there is no ETA on a fix for this issue at this time..
Updates? Solution?
Stock LS7 manifold volume is 692 cu in.
MSD LS7 manifold volume is 1000 cu in.
Can you post it in the tune repository on the main site: hptuners.com?
Looking for the ecu changes for the different supercharger heat exchanger configuration in the 2017 model.
Also looking for...
I need a 2017 C7 Z06 stock calibration file, manual transmission preferred.
2016 LT4 HPTuners log.
Ambient 70 degrees, IAT 77 degrees, IAT2 88 degrees, Manifold temp 174 degrees.
Cylinder air mass .35 grams, IAT advance -2.8 degrees.
IAT Spark Advance Correction table...
Need the CAN ID for manifold temp so I can add it to an AIM data logger.
Can anyone help?
HPTuners shows IAT2 at manifold temp in the calibration file. But it does not map correctly in the scanner....
Is the IAT spark advance correction table using Manifold Temp PID?
Logging LT4 (C7/Z06) IAT, IAT2, and manifold temp.
I am assuming manifold temp is air after the internal heat ex-changers in the super charger that is being fed to the cylinders, IAT2 is the temp...
Which version of HPTuners are you using?
3.2.149 I am using will not open the file.
Thanks
Anyone have a 2017 C7 Z06 stock calibration file they can post?
This is the list from 2.24
63101
This is the 3.xx channel cfg with the transform
63100
Log file
63103
Problem loging AEM 30-0333 wideband with the MPVI internal logging.
Works fine when using a PC. Does not log the channel when using the interface logging funtion.
Channel config loaded in the...
Need help with a transform. I have several laboratory grade non-linear (temp, egt, linear ride height) 0-5 volt inputs that worked fine in all previous version. Not suported in 3.xx! HPTuners tech...
2.24 shows MPVI 4 as oil temp and displays a reading in F.
Not supported in 3.0.xx because the histogram is a nonlinear formula.
MVPI 4 in 3.0.xx shows unsupported ID number.
I have a copy of...
The first 2.24 log I posted had a limited number of PIDS. It was a log recorded in the MPVI interface.
Full 2.24 log attached logged with a computer.
57536
In the 3.0 channels MPVI 4 is oil temp with a non linear transform but the 2.24 log file MVPI 4 output is not compatible.
In the 3.0 and 2.24 MPVI 2 & 3 are 0 to 5 volt inputs that need a user...
2.24 log and 3.0 layout + channels.
Thanks for your help.
57531575325753357534
STACK oil temp gauge with a nonlinear voltage output vs temperature.
<add key="4" value="Oil Temp,Oil
Temp,17,10,0,0,0,0,0,60,66.667,73.333,80,84.286,88 .571,92.857,100,101.429,10...
"looking at old logs is only worth so much"
But if you have 2.24 logs from dyno runs with different configs the data helps on vehicles you tuned over the past few years.
Problem is MVPI inputs are...
When replaying a log file created with 3.0.XX the graphs populate all the data in the cells at open before playback started.
Is this normal? 2.24 populated histogram cells during playback.
When...
Problem solved. Your formula was correct.
Layout was imported from a 2.24 gauge file. PID for oil temp sensor (dry sump oil tank) was active in 2.24. and is not active in channels in 3.0.55. Generic...
Not sure what I did wrong. Oil temp displays 208f in channels when the actual gauge shows 140f and -40f on the gauge in the display.