👍👍
Type: Posts; User: Blueboy
👍👍
Think I found them.
Under Generic Sensors
Under Engine
Under air flow
Mass Airflow (mass flow rate)
And
Manifold Absolute Pressure (pressure)
Then
I can't find AFR cmnd, MAF, MAP.
Back in the good ol' days all we had to work with was timing, fuel and air (for the most part).
Now a days there is all kinds of cool stuff to tune an engine.
What would be the most important...
Thanks IARLLC! I have no idea what system I need. All I want is the ability to change the BCM functions on my truck.
If you can point me in the right direction or passably post a link I will...
13 minutes into the video he talks about copying the high octane spark table and pasting it into the low.
A different guy on boobtube says thats a bad idea because your taking away the knock retard.
Thanks kyle_Customizer! If I understand correctly I can get the MongoosePro? GM 2 for $495 and the Tis2Web Reprogramming that needs a 2-Day subscription for another $55. Is that it or is there more...
From what I see on-line the tech2 is a thing of the past. Not sure when the last year is you can use one. But it would still work for my needs. GM now uses MDI, Multi Diagnostic Interface. The cost...
Is there a way to change the set pressure warning for the Tire Pressure Monitoring System?
Also the remote to unlock the doors? I want to be able to unlock both doors with one push of the button.
Ya that would be the easy way of doing it but I can't find my flash drive.
Anyway, long story short, all is good!
The write did fail about 5 times but it finally was a success. I had that...
Finally! 10_SS thank you very much!!
OK didn't save changes and deleted that file. Glad I don't have to uninstall HPT and start from scratch.
I will put back the stock file from my old...
Understood. But that doesn't answer my question.
Can I follow the steps in saving, even after I closed and reopened the page 5 times??
Or can I delete the current file I did the enhancement in...
I do have a stock file in my other computer.
Can I delete the current file I did the enhancement in and forget this ever happened?
:hi:
OK, Think I'm getting the gist on this OS enhancement. Still a lot of reading and re-reading to do. I hate reading!
I didn't realize poking around would bite me. I thought it was just...
Definitely!
What are my options at this point?
I could follow the instructions 1-4 BUT !
The steps what I did:
Started with this, clicked "apply code modification"
67608
Actually, it didn't say anything. Down at the bottom, nothing like do not select this!!
67599
I didn't do anything yet.
So do what it says and I should be ok?
What do I do with the stock program?
Hope I didn't do anything stupid. I clicked OK...
If I did something stupid what now?
67597
Ignition has to be on, no accessories. There are a lot of extra thinks on and running. The dash is lit up like a Christmas tree and I can hear what sounds like the heater motor running, even though...
Writing to my truck failed. It got over half way and stopped, I closed the vehicle writer, tried again and it worked fine. What would cause that?
Then when I was finished I closed the program and...
I'm in the same boat.
For me, I need something a 3rd grader can understand.:pray: This HPT program is really cool but what does what is overwhelming.
I will be following this thread, hopefully...
Thanks again 5fdp!
I was thinking that would be the way to go.
I’m no expert but I have read on the WWW that you can get both NB and WB from one wideband unit using a narrowband simulator. That...
My AEM 30-410 wideband came in yesterday!:D The instructions say to weld the bung 18" from the exhaust ports. And at least 36" if you expect EGT's over 1500* or turbo or extended high RPM's AND...
I know you said "-Multiple new AC DELCO plugs gapped at .40" but a friend of mine had a misfire on #5 when in fact the #8 plug was cracked.