I was wondering if anyone had a file from the GM Performance LS376/525 Controller Kit I looked in the tune repository but it lists everything for year make model.
Type: Posts; User: LILFREDDIE
I was wondering if anyone had a file from the GM Performance LS376/525 Controller Kit I looked in the tune repository but it lists everything for year make model.
I went to add my read entire file and for some reason I could not find it so I came to the car to read entire and now its says "invalid application key" wont let me connect. for some reason my...
I am trying to help my brother in law get his project to start, he purchased a beautiful harness from Mark Cambell at Street and performance. Unfortunately Mark died RIP he was very helpful to my...
I reflashed an ECM on a 2006 1500 and I am now getting some throttle body codes and now truck wont start. P0606,p1258,u0107. I just bought the credits for this truck, trying to help this customer get...
Bill i've been looking for the help file do you have a link for it Thanks.
thank you Russ K.
bill truck runs great but cant't seem to get the numbers right on the hg it should be 101 with the key on engine off but its showing half that. what did i do wrong?
Bill it would be nice if I could go back to my stock settings on my gen three and calibrate a 2 bar map so i could log boost. The calibration settings are only available in my 2 bar SD tune.
Been searching forums to no avail, LQ4 408 single turbo 4l80e. I want to go back with MAF and keep my 2bar MAP. I now have my ltft and MAF trims set and with the MAF installed but the truck is not...
dammit scan I posted was actually me disconnecting ect in order to see what happened I will make the timing changes tomorrow, as far as SD no error reported and MIL on first error what is the...
took them apart pins look good, if i where having a problem with the pins would the truck act funny or die while driving? It never stalled or acted up while running i only have problem when starting...
are you talking about the wiring harness side i will check them right now
Tried clear flood mode no avail, noid is not lighting up when no start condition exists. injectors are not firing, have spark though! weird stuff happening.
i have twin pumps, twin corvette regulated filters going into each a rail with crossover in the front, returnless setup. Maf is setup to MIL on first error. I am running SD, i was just trying 20%...
please if anyone could help
Just about ready to pull my hair out. 01 silverado 2500 swap into an 85 silverado. I am running 2 bar SD tune on a built 408, cam, Victor Jr, Elbow, 93mm TB, Comtech billet fuel rails, 60lb...
i am having the same problem have to unplug usb for it to connect again
if so what was the problem?
Its very rare that ecm's go bad, were you getting a specific code that makes you think it is bad?
Bill I am having a problem with my 01 silverado with an SD tune it will occasionally not start after...
i down loaded the editor software everything went smooth but when i try and ping it says it can't communicate as well. So i tried installing it in my home computer last night and it did the same...
My laptop is in the shop so i installed HP tuners in my daughters dell every thing went well but it won't recognize when plugged in to the laptop.
how is it running Mitch? give me a call.http://www.youtube.com/watch?v=q0jbFVpzRsE check out my flip video
I am having a problem with my scanner, when i log i am not getting it to show boost. my PID is set up like this with a 2 bar MAP [SENS.30.IMP]-14.5 . it won't show boost i just may have a bad 2 bar...
What is your fuel pressure with a gauge?
I am new to tuning and I need some help with my turbo project. I am planning on going to Tuner school in January but I am trying to just get my truck to idle and drive it around a few miles so i can...