Any one have a tune file from a 19' Camaro SS with 10 speed? I am using the HHP TCM in a 2020 Camaro and would like to compare some things.
Type: Posts; User: shoaf85
Any one have a tune file from a 19' Camaro SS with 10 speed? I am using the HHP TCM in a 2020 Camaro and would like to compare some things.
Ground wire above starter was broken.
Welp aside from going over all the electrical connections etc etc I have no idea what is going on with this car. The car will shut down almost like its going into REP mode during pulls but will give...
I have a 2004 CTSV with a P59 pcm and some big injectors. The transient table is not in his tune file and I'm not able to get the ide fueling leaned out. Any insight on this. First time experiencing...
2016 atsv on the dyno, has the new era 600 hp package. I have read all the threads on here and have made small adjustments back to back without any luck.
tune file and log below (iR* is the...
Started over with base file and it?s working now. Guess i fat fingered something possibly. Shoulda tried this before posting. All good now
I have a turbo C6 grandsport here that I am tuning. I had the car running in sd on the stock operating system. Now we are raising the boost a good bit and I switched to the custom 2 bar. After doing...
Maxed out p0068 etc table and that fixed it.
Quick run down. Forged LSA setup custom F1X blower setup. DSX fuel system DW 1500 cc inj.
At first I only did the double stoich method for scaling but then hit the airflow limit (2.56g) at...
I was able to fix the issue by using his diablo handheld to set the gear ratio and it worked fine!
Customer brought me his car to remove the sct handheld tuner and do a custom tune on the car. I returned the tune to stock calibration via the handheld and read the file. I then made my changes to...
2016 Whipple SS Camaro that we just did a cam in. I have done several of these with auto transmissions and never ran into this. This is the first manual one with this setup.
Has BTR blower cam...
New converter installed and on the dyno this thing shudders horribly in 5th and 6th. If I unlock converter via vcm controls it goes away instantly. I have set the tcc slip tables to 0 in 5th and 6th...
It wasn’t real knock. As soon as i found the ground wire and fixed it the same calibration had ZERO knock. I knew it wasn’t seeing knock by reading the plugs......
I always keep them the same when tuning ve and maf separately but will change back when I’m finished and convert the tune beck to a blended file. We have many setups that don’t even use knock sensors...
Found the issue. Ground wire was not connected on the side of the block. Bolt just above the driver side knock sensor!
What type of fueling issues are you seeing?
The tune isn't finished up yet but the afr is not far off!
UPDATE NEW PLUGS DID NOT HELP
As far as fueling goes yes the fuel is good. Pressure is holding steady at 60psi throughout and lambda is .85-.87 throughout the pull. AFR reading is in the logs. The...
LS7 forged pistons, AI heads and custom PatG cam. BR7ef plugs with out of the box gap
Alright guys I've got a C6Z on my dyno here and we are getting some pretty aggressive knock. I noticed it on...
Fixed it, thank ya sir! Never maxed that out before but now I know not too....
Ahhh i see. Thanks man!
Just finished tuning this car on the dyno and it shifted perfectly on the dyno in "D" and in "S" mode. Once I pulled it off the dyno it would shift up through the gears once but would never downshift...
I typically do use the 2 bar OS on all my turbo tunes. I've used the ZR1 map with vve tuning once before and so far it has worked well. The car is monitored and I haven't noticed any fuel swings etc
I found the issue. Under the fuel tab there is an enable and disable tab for the Cylinder Gain, somehow (fat finger I guess) that was enabled. It is disabled in the oe file so I switched it back and...
Tuning a rear mount turbo A6 C6. The setup is very simple.
ECS Boost A Pump
ID1050x injectors
Rear mounted S475 turbo
The 3 mods listed above are THE ONLY MODS on the car period. I have...