Search:

Type: Posts; User: lxcoupe

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. E92 / L86 Swap Having Trouble with Fuel Pump Priming?

    Hey guys I have a 2020 L86 and E92/ T87a setup in a 77 C10. I cannot get the ECM to send 12V to the fuel pump relay. So far I've disabled VATs and disabled Starter Diag. Is there anything else...
  2. Replies
    1
    Views
    1,280

    MPVI2 Pro vs MPVI2 with Pro Link Cable

    Hi wondering what the difference between an MPVI2 with a Pro Link cable and the MPVI2 Pro? I assume there's a firmware difference between the two and if so can I pay to update my firmware?

    I'm...
  3. Transferring Vehicles from MVPI-1 to NGauge ?

    I just bought an nGauge and was wondering if I can use it to tune all the vehicles associated with my MPV-1?
  4. Still fixed?

    Still fixed?
  5. Did you resolve this?

    Did you resolve this?
  6. How Important is it for Flex Fuel Sensor to have 12V *During Cranking*

    There are two methods of powering the flex fuel sensor... 12V key-on (cuts 12V while cranking) and 12V ignition on (keeps 12V while cranking). Is it mandatory that the sensor maintain 12V during...
  7. 416 LS3 Base Startup File, A Little Guidance ?

    So I have a basic n/a 416 with a small cam using all LS3 sensors including stock LS3 injectors, LS3 MAF, etc. I plan to start with an L99 Camaro base file and I just need to get this thing started...
  8. Replies
    3
    Views
    1,647

    6L90e T43 TCM - Which PCM ?

    Hey guys, I have a 2018 Express Van 6L90e. Having a harness built and I don't have a PCM yet. I'd rather not remove the TCM from the trans if I can avoid it, so any guidance as to which OS I can...
  9. Seeing if you figured this out? I also just...

    Seeing if you figured this out? I also just obtained a 2018 Express Van 6L90e for my swap project.
  10. Replies
    4
    Views
    2,267

    Is that done through VCM editor or the forum?

    Is that done through VCM editor or the forum?
  11. Replies
    4
    Views
    2,267

    2019 Camaro SS Support?

    Are the '19 Camaro A10's currently supported?
  12. Replies
    2
    Views
    1,242

    VIN Swap from P12 PCM to E67 PCM

    I completed a 5.3/T56 swap in a 2006 Chevy Colorado using a E67 PCM from a 2006 Cadillac CTS-V. Is it possible to write my original VIN onto the E67 PCM? The Colorado originally ran OS # 12593533
  13. Credits Question for E38 ECM/ T42 TCM for LS3/4L80e Swap Application

    I'm doing an LS3/4L80e swap in an old C10. I know I need an E38 ECM/ T42 TCM. A good place to get this combo is a 2008-2009 Express Van or 2008-2009 Silverado. I'll be buying them used, individually....
  14. Replies
    0
    Views
    816

    ECM/ TCM for LS3/4L80e Swap Application

    I'm doing an LS3/4L80e swap in an old C10. I know I need an E38 ECM/ T42 TCM. A good place to get this combo is a 2008-2009 Express Van or 2008-2009 Silverado. I'll be buying them used,...
  15. Replies
    2
    Views
    1,068

    LS3 Injectors Modified to Flow 60LB (FIC)

    Hey guys, wondering if someone can explain something to a newb. I have a set of factory LS3 injectors modified by FIC to flow 60LB. What, if anything, is changed in a base tune so that the vehicle...
  16. Replies
    6
    Views
    3,844

    Thanks, where'd you find that file? It's nearly...

    Thanks, where'd you find that file? It's nearly identical to a stock file from the looks of it.
  17. Replies
    6
    Views
    3,844

    Anyone have a basic 91 octane 5.3 tune?

    Hey guys, just got my swap running... an 89 Dodge Dakota Shelby with an 03 Yukon 5.3, 4L60e, stock manifolds, true duals with no cats, and an eBay cold air intake. I've found a few 4L60 articles,...
  18. Trouble with VIN Swap Tool after New Computer

    Hey guys, I'm running a 2005 Avalanche flex fuel OS on my 2005 Silverado. I've paid for both licenses and they both show up in my licenses list. But when I read the Avalanche OS off my truck, then...
  19. Replies
    1
    Views
    1,227

    I seem to have resolved this by comparing tunes...

    I seem to have resolved this by comparing tunes in the tune repository to my own. The "Desired Throttle Area" table was really aggressive, I copied over several tables from other E38 turbo trucks...
  20. Replies
    1
    Views
    1,227

    Excessive throttle sensitivity

    Hey guys, I have always experienced an extremely sensitive throttle on my turbo charged 05 Silverado. Stock throttle body, and no other issues. I can step on the gas and it's very touchy, and if...
  21. So I've transferred everything over besides...

    So I've transferred everything over besides "Offset vs. Press vs. IGNV", still not sure what to do about that table.
  22. Question on Copying Injector Data - Offset vs. Press vs. IGNV Different

    I've read that there are 5 various parameters that need to be modified in order to properly control the injectors. I am trying to copy over the injector data from a LC9 flex fuel Avalanche tune over...
  23. Thank you, I must have the right cam gear...

    Thank you, I must have the right cam gear installed them.
  24. Basic question, would a 1x cam gear even fire on a 58x motor?

    All else being in order, if a 58x Gen IV motor had an LS6 cam installed and the installer used a 1x cam gear instead of a 4x, would the motor even start?
  25. LC9 Swap Into Colorado (ex-4cyl), Runs great but lopes and 10mph

    Hey all, I have a 2006 Colorado with a LC9 5.3L (58x) that we did the dod and afm delete and installed a LS6 cam, LS6 intake, and headers. I used the LC9 36LB flex fuel injectors from the truck...
Results 1 to 25 of 51
Page 1 of 3 1 2 3