Search:

I know of a good tune done with EFI live. Can I upload the tune in HP tuners & read the different tables & compare the files.
Scot

Could someone post the mapping for a LS6 MAF. I have been told to remove the resister in my 85 MM SLP MAF & use a LS6 mapping for starters.
Thanks,
Scot

Thank you,
I was actually was looking for the VCM control under Special.
I still had problems with not being able enable test. I stopped the scan, went to special screen. Could get the balnce test...

I opened my HP scanner program, under the display tab, I clicked on DTC's & Emissions, Readiness & Diagnostic tests & tried to pull up the Diagnostics info screen. It is blank screen on a Blazer &...

I opened my HP scanner program, yhe under the display tab, I clicked on DTC's & Emissions, Readiness & Diagnostic tests & tried to pull up the Diagnostics info screen. It is blank screen on a Blazer...

I was refering to the HP Tuner Help menu for the topic your on.
I pushed F-1 & I got the windows help menu. Is something wrong with my software load?
Scot

Is there an F-key that brings you straight to the help topic you are working on. This would be very useful. Scot

I figured out what I was doing wrong. I did not list certain addresses on table display so they could be seen. Such as "Mass Air Flow" in Hz, & "Air fuel Ratio Commanded Hi Res(afr)" & I also had to...

I am trying to log my Wideband through my HP scanner & can't get it to work. I configured my LM-2 as Lambda, Seems to work. I see it reading at EIO input#1.

Then I configured Commanded Lambda by...

Can somebody check this out & tell me what I am doing wrong.
I configured my LM-2 as Lambda reading
Configigured in the input # EIO#1. I seems to work fine. When I hook it up to the scanner the...

I disconnected the air pump & piping while installing my headers. Where do you disable the pump & what is it going to do with the tune?

Thank you for your words in advance. The Blazer lost a catalystic converter. I took it out & ever since then it hasn't ran well & has gotton bad gas milage. I know its got a new spider injection so i...

Can you Explain PE looks way off?
I copied this from a car that runs really well. It is set up, to retard the timing for Nitrous. Which I would not use at first.
But as I am starting to learn the...

Can you recomend a reasonable priced wide band.

Here is the file for this 2000 Blazer. Cat removed

Could you guys look at this tune & tell me what you think? It is from a 2002 stock firebird ls1, 1-3/4" Headers, no cats, ported stock tb, stock MAP.

Can I hook up my pro system up to a friends car and suck his program without paying for credits? He already paid for credits through somebody else. Can't get ahold of the guy. I just want to compare...

I removed the Catalytic converter on my 2000 Blazer w/4.3 engine. Is there anything you do to the stock program?
Scot

I defiantly am going to get tuning down before the Nitrous goes on.
Thank you for looking out for me. I am just asking for knowledge..

I was told in 2002 WS6's they have a timing chart. When pin i think 28 goes to ground the nitrous timing sets back the timing.
Could they be using the low octane timing table?
Or is there a...

I posted my tune. I really appreciate you checking this out for me.
Do you know how to enable the nitrous oxide time table & where it is? What pin you use & how to?
What the good nitrous kit to...

This is my current tune with Gears & tires size changed.
Anything you can do to help would be appriated. I am going to port the manifold side of the thottle body. Does any body have any pictures of...

I have a 2002 WS6 with a stock LS1 motor w/6 speed. It runs good as it is. I am about to install a set of 1-7/8 Texas Speed & Performance headers with their off road Y pipe.(no cats) deleting...