Search:

Type: Posts; User: JoshMass

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    53
    Views
    58,941

    I wonder if that's the fuel injector that ZZP was...

    I wonder if that's the fuel injector that ZZP was broadcasting about on their FB page recently.
  2. I found the same thing to be true on my E40 tune...

    I found the same thing to be true on my E40 tune Chris. I've set the idle timing to match HO timing and it will not add timing beyond that number when the idle RPM drops below desired RPM. I have the...
  3. Replies
    44
    Views
    22,867

    Good to know. I wasn't sure if the DBX controls...

    Good to know. I wasn't sure if the DBX controls were going to be enough. I added a laminar flow insert to the MAF to smooth out the idle issues I was having due to it's placement immediately after...
  4. Replies
    44
    Views
    22,867

    FWIW, I'm having the same issue with my E40 tune...

    FWIW, I'm having the same issue with my E40 tune on a 05 GTO. I also have an Abaco MAF setup and was wondering if it was something that could be tuned out with the Abaco software rather than in the...
  5. Replies
    422
    Views
    288,629

    I may have answered my own question. Looking at...

    I may have answered my own question. Looking at this thread it seems that I have to adjust the HOM high and low tables. Never thought about that part.
    ...
  6. Replies
    422
    Views
    288,629

    Idle Issue

    I have a question for those of you more knowledgeable than I. I've been trying to get the idle dialed in and have been having something odd happen regardless of the changes I make.

    Take a look at...
  7. Thread: gms1 kpa

    by JoshMass
    Replies
    8
    Views
    4,158

    I'm curious if this would provide a different...

    I'm curious if this would provide a different result than [PID.2338.PSI]-[PID.2340.PSI]?
    Is there any difference between BARO Sensor and Barometric Pressure (SAE)?

    The only reason I ask is that...
  8. Replies
    56
    Views
    36,188

    Does it do anything to increase the P0106 high...

    Does it do anything to increase the P0106 high range to 304 kpa? At 4.75 volts the corresponding MAP should be 307kpa if I'm not mistaken (gimpster chart). If the high voltage fail is 4.9v I would...
  9. Replies
    67
    Views
    32,982

    Someone else gave me the same PID configuration...

    Someone else gave me the same PID configuration but I'm curious if it will provide any different result than [PID.2338.PSI]-[PID.2340.PSI]? Is there any difference between BARO Sensor and Barometric...
  10. Replies
    15
    Views
    9,429

    Although this doesn't go into the tuning aspects,...

    Although this doesn't go into the tuning aspects, take a look at this paper at MIT that does the analysis of using E85 on the LNF.
    ...
  11. Replies
    233
    Views
    142,086

    The more I discover the more I realize that this...

    The more I discover the more I realize that this statement is absolutely on target. I have used all the major LNF threads to learn as much as possible but mainly so that I can be an educated...
  12. Replies
    233
    Views
    142,086

    The biggest thing that helped me understand the...

    The biggest thing that helped me understand the cam timing, before I got on the dyno and played with it, was watching this video put out by Ben Strader at EFI University.
    ...
  13. Replies
    422
    Views
    288,629

    I'm aware of that part. I just hadn't looked at...

    I'm aware of that part. I just hadn't looked at the new parameter release since March and totally forgot about the desired and actual FP PID's being added.
  14. Replies
    422
    Views
    288,629

    Thanks! I have the 2.23.256 beta. I'll look them...

    Thanks! I have the 2.23.256 beta. I'll look them up tonight when I get home.
  15. Replies
    422
    Views
    288,629

    I just read through this whole thread again and...

    I just read through this whole thread again and didn't see a solution to logging fuel pressure. I know that a few of you are logging fuel pressure but I've searched all morning and can't find the...
  16. Replies
    21
    Views
    7,429

    I understand that currently the piston of the...

    I understand that currently the piston of the HPFP cycles at 1.5 times the engine rpm. I'm assuming that increasing it to 2 times the RPM (4 lobes) will allow us get more fuel in the cylinder within...
  17. Replies
    73
    Views
    51,948

    Is all this KR still showing up after clocking...

    Is all this KR still showing up after clocking your knock sensors at 90*?

    http://www.hptuners.com/forum/showthread.php?t=30115&highlight=knock+sensor+lnf
  18. Thread: Advice needed

    by JoshMass
    Replies
    2
    Views
    1,469

    Am I asking the wrong question? 37 views and not...

    Am I asking the wrong question? 37 views and not a single response.
  19. Thread: Advice needed

    by JoshMass
    Replies
    2
    Views
    1,469

    Added the config file to original post.

    Added the config file to original post.
  20. Thread: Advice needed

    by JoshMass
    Replies
    2
    Views
    1,469

    Advice needed

    I'd like to get some opinions from those of you out there that have a lot more experience at this then I do.

    I've just completed the ACP course from EFI University and was working on the...
  21. Replies
    0
    Views
    1,134

    Opinions wanted

    I'd like to get some opinions from those of you out there that have a lot more experience at this then I do.

    I've just completed the ACP course from EFI University and was working on the...
  22. Thread: OBDII cable

    by JoshMass
    Replies
    22
    Views
    18,885

    Thanks. The research that I've done so far is...

    Thanks. The research that I've done so far is split 50/50 on whether or not it will work on CAN. I'll continue to poke around in the meantime and work on a backup plan.
  23. Thread: OBDII cable

    by JoshMass
    Replies
    22
    Views
    18,885

    I'm about to do the same thing here. I need to...

    I'm about to do the same thing here. I need to add EGT monitoring to the Aeroforce but want to datalog using HPT at the same time so that i don't have to wire up two gauges. When you did this, was...
  24. Replies
    239
    Views
    115,359

    Boy did I stumble on this thread at the right...

    Boy did I stumble on this thread at the right time! I missed out on all the angst while working on the mechanicals of my build. We should be tuning in less than a month so it would be great to see...
  25. Replies
    4
    Views
    2,648

    Wow. Disappointing.

    Wow. Disappointing.
Results 1 to 25 of 27
Page 1 of 2 1 2