Step 1 - go to Hptuner website and look at the supported vehicle list. If your vehicle is not in the supported list, we cant help you.
Step 2 - BUY MPVI3 and credits required to license your vehicle...
Type: Posts; User: danmw2003
Step 1 - go to Hptuner website and look at the supported vehicle list. If your vehicle is not in the supported list, we cant help you.
Step 2 - BUY MPVI3 and credits required to license your vehicle...
You're obvioulsy a little green at this. My best advice to you would be to make sure you're thorough. Dont rush through jobs. Do it right the first time so you dont have to go back and troubleshoot...
Cam chopping should not rattle bolts loose. It was left loose. Torque wrenches are you friend.
Sounds like a whole lot of people involved, who arent qualified.
Im using windows11 with HpTuners. Works just fine, you cant open old version of logs or tunes with newer software. If thats what you're trying to do. Thats not a windows 11 problem.
I will say this. I've had remote tunes from a handful of others over the years. Even had Pat G do my G8 at one time, years ago. GHuggins, has been the best one I've dealt with. The patience this man...
Im not going to tell you prices, because the tuners here set their own prices for what they're doing, but with regards to GHuggins, I would say money well spent and that you get what you pay for....
Definitely going to hit him up again in the future.
Yeah, these guys are F***'n awesome here on this forum. I applaud them all as well. They all put some much into this forum, and its greatly appreciated. They may argue with each other at times, but...
I agree, simply because I have done this myslef. Not knowing any better. In fact, I'm pretty sure someone here on this forum corrected me on this at one time, when I asked for someone to review my...
I always check pushrods for various, and legitiment reasons, but its not always the pushroods fault for wiping out a cam lobe. Incorrectly set up springs are just as likely to take out cams as an...
Oooh! I wanna see that crystal ball!!!
Sounds to me like you need to properly adjust your shift cable. Tune wont fix that.
0x10 means its a permanent code. Which means you cant clear it. It has to be fixed, and the ECM does its own test and clears the fault. Your factory remote start doesnt work at this point.
You should degree in the cam and make sure its on the correct installed centerline. You should also measure pushrods, just popping in whatever the kit comes with, can be hit or miss, and potentially...
If you were just asking the question of "can it be tuned out" but you havent purchased any tuning equipment, then yes. You need to tune it and turn off codes and disable the DoD in the calibration. A...
Maybe a bigger hammer?
I feel like injector duty cycle being so low, likely near its lower limit causes some of this. Injectors cant possibly be accurate at or near its lower limit. I could be wrong about this, but I...
Tuning can be complicated. There's a lot to learn, and it takes a LOT of time to learn it. Pay someone if your don't want to spend the time tinkering and want the thing to run right.
Just want to give a shout out to GHuggins for a job well done. Never before have I had anyone, be as thorough as he has been, tuning my car. He really took the time to go through and get the VE, MAF...
It's unfortunate because it turns into group think with its members. Any discussion outside of their beliefs is immediatley attacked. Makes it hard to get them to think outside of that. Thus causing...
Camaro5 forum is choke full of backyard habbyists, backyard mechanics and supposed dealership mechanics who think they know everything. Giving technical advise to people there is like talking to a...
Sounds like he wants burnt exhaust valves. Someone should kindly help him with his tune, so he can do that.
I've found, with a manual transmission messing with this setting makes it harder to feather the clutch when taking off from a stop. I didnt like it at all. It can be too responsive, at least IMO. I...
Use a different browser.