New to 3.0, graph's not populating

[Funkybird]

Just downloaded the other day and have been tinkering. I've got alot of it figured out except none of my graphs will populate while scanning?

[schpenxel]

Post a log

Usually it's from not logging the right things

[rickshoe]

I to am having the same issue since the v3 update. I tried to scan a graph on my 2010 Tahoe it only populated numbers on the .04 cylinder airmass top line under Rpms and wouldn't show anywhere else, contacted hp tuners help and was advised there was nothing they could too help, they couldn't point me in the right direction on what was wrong, 2.24 scanned perfect every time. Thanks customer service.I would love to find the solution to this problem as well

[schpenxel]

If you'll post a log and your layout I'll show you what's wrong.

[rickshoe]

thank you i have attached 1 that i sent to hp tuners, what i was trying to log was spark knock right now because its pinging bad right now and ended up having to put back to stock before damaging motor. its just a test because as said only the top row was getting info, im stumped and new, very appreciated too

[schpenxel]

Need your layout also.. It's something not setup right with that. The log works fine for me

[rickshoe]

Need your layout also.. It's something not setup right with that. The log works fine for me

so I have used this config with no results and the default layout also supplied with the scanner , settings were under default under layout, diagnostics,o2(mv),airflow(g/cyl), like i say charts is working but not graphing properly, top line populates but everything from .08 down nothing

[schpenxel]

Open up scanner and go to layout-->save layout as, then save it somewhere.. and then post that file. That'll let me see what you're seeing

Trying to use a 2.24 .cfg file in V3 is not a great proposition.. it works the best it can, but it's not perfect.

If you can post your current layout file I can show you what's wrong. Layout file will include all of your charts, graphs, gauges, etc. So it will let me see pretty much what you're seeing which I think will make it easy to spot the issue.

[rickshoe]

here the default I've been trying, also tried to set sensor to knock sensor with no results, thank you for checking this for me, and sorry for high jacking thread hope other guy is getting some info here too!

[schpenxel]

You aren't logging cylinder airmass... try adding it to the list of channels and everything should work

I've changed the attached layout to use a cylinder airmass that is calculated based off of the MAF reading, but that will only be accurate when tuning in MAF only mode.

Adding cylinder airmass to the list of channels you're logging should get the layout you posted working though..

rickshoe.Layout.xml

[rickshoe]

You aren't logging cylinder airmass... try adding it to the list of channels and everything should work

I've changed the attached layout to use a cylinder airmass that is calculated based off of the MAF reading, but that will only be accurate when tuning in MAF only mode.

Adding cylinder airmass to the list of channels you're logging should get the layout you posted working though..

rickshoe.Layout.xml

thank you so much for having look at this i will give it a try here. i will post back to let you know if this is good now, so appreciated
Richard

[rickshoe]

thank you something so simple made this a pain in the ass, but now this is populating now, thank you again so thankfull for you taking the time to look at this, if you were near by by id by you a case

[schpenxel]

No problem!

[5_Liter_Eater]

And don't forget, save the channel list, or when you come back into the scanner after closing it, it'll be missing cyl airmass again.

[rickshoe]

And don't forget, save the channel list, or when you come back into the scanner after closing it, it'll be missing cyl airmass again.

You bet already done, not going through this again