go the 411 pcm. nothing to it and runs like a champ
My setup is a 356ci with a 260/268 (212/218 at .050 lift) duration cam with aluminium corvette heads and flat top pistons running 11.3 comp. ratio. with tuned port injection and vortec crank pick up and dizzy running a 411 pcm and 60lb bosch injectors, 1.6 ratio roller rockers. For transmission its a 4l65e built with the monster in a box mega ss kit. All in a 92 chevy ext cab 4x4 pickup with a 98 cab now installed with a third door! running only e85
I got lextech's excel file for 96 and 98 trucks to 411 pcm. Pm me
My setup is a 356ci with a 260/268 (212/218 at .050 lift) duration cam with aluminium corvette heads and flat top pistons running 11.3 comp. ratio. with tuned port injection and vortec crank pick up and dizzy running a 411 pcm and 60lb bosch injectors, 1.6 ratio roller rockers. For transmission its a 4l65e built with the monster in a box mega ss kit. All in a 92 chevy ext cab 4x4 pickup with a 98 cab now installed with a third door! running only e85
just within last couple months
My setup is a 356ci with a 260/268 (212/218 at .050 lift) duration cam with aluminium corvette heads and flat top pistons running 11.3 comp. ratio. with tuned port injection and vortec crank pick up and dizzy running a 411 pcm and 60lb bosch injectors, 1.6 ratio roller rockers. For transmission its a 4l65e built with the monster in a box mega ss kit. All in a 92 chevy ext cab 4x4 pickup with a 98 cab now installed with a third door! running only e85
My buddy is in the middle of installing a 2000 chevy 7.4 vortec into a 1990 chevy 1500. , Origonally when he removed the 7.4 he cut and marked each wire so he could reconnect after installed, unfortunately all his markers got wet and are unreadable now. does anyone have the pinout for this? The ecm number is 16263494 and the 2000 truck did have C6P option. Any help would be greatly appreciated, this poor guy is at the end of his rope and truly needs help. I thank you in advance for any and all help.
Email me if you need anything else
caleditor@pcmcalibrators
I am sure that I do. I have over 1000 files
Just send me an email
I have a 97' Vortec 5.7 in my 86' k10. It has the stock computer with a tune for his set up. It came from a friends show truck who upgraded to a 6.0 lq9. He had a supercharger on this engine which i didn't buy. I've ran the truck a few hundred miles but i need some tuning done because his gear and tire set up was different than mine. He had 38" tires with 4.88 gears and the Whipple blower. I have 4.10 gears and 39.5" tires and don't have the blower. The rev limiter is non existent and the truck will not shift out at wot. I cant find anyone around here to tune it because of the year. I would like to do a tune where the person actually drives the truck. What other options do I have such as computer/upgrades?
Thanks for any suggestions.
Jeff
If nobody around you has software to tune those vehicles, the cheapest option is to buy Jet Dst and tune it yourself.
Jet is not the best and customer support is garbage, but it is the cheapest option for end user.
9 sec Montecarlo SS
I did the 411 swap a month ago and its running great. The swap didnt take too long 4 hrs or so. Thanks to Lextech, he hooked me up good!!
still no support for editor on the blackbox ,
sorry to bring up an old thread
jim
wont work with emissions here in Md , they read the vin , then im back to square one ??? this is getting tough because i still wont be able to use my 411 with hp
the only way around it is two pcm's programmed the same , one with the vin and one without
I am new to the forum and HP tuners. I have a 95 C3500 2wd with 4L80E and a 96 Vortec 7.4L engine and PCM. I have the pin outs and am waiting for parts from to complete the PC 0411 swap. I have a 0411 from an express van with 5.7L. Where would I find a base file for this truck. This truck I am working on has a set of Ford Racing 24lb fuel injectors in it. Thanx from a newb.