VCM Suite 3.2 is here!

[LSxpwrdZ]

Thanks so much! I pretty much got it now. Had to choose the generic sensors.

Also another question. I am running speed density, in the scanner its all charting map in kPa vs rpm which is all fine and good. But in the editor when I'm tweaking the spark table, why is it cylinder airmass in grams? Can I go off the map instead? Just to keep thing uniform.

The Timing table uses cylinder airmass as it's load variable while the VE is based on manifold pressure. The Axis cannot be adjusted to match simply because they use two totally different parameters as measurement of load.

[schpenxel]

You are quite right about that--I misunderstood the question

[wasyl]

The Timing table uses cylinder airmass as it's load variable while the VE is based on manifold pressure. The Axis cannot be adjusted to match simply because they use two totally different parameters as measurement of load.

and there is no way to change that ? it would be much easier to have all loads by one sensor and MAP is the easiest way to use/read/understand
best regards

[schpenxel]

No.

[realcanuk]

3.2 seems to always open as a small window, while other versions used to open as I last closed them. Is that for everyone or is it something on my end. Just wondering.

[Keith@HPTuners]

If you're using an older version side by side, your settings will not work as expected.

3.2 should remember your size and location correctly.

[realcanuk]

If you're using an older version side by side, your settings will not work as expected.

3.2 should remember your size and location correctly.

Just played with it a little further.

I am not running any older versions. Whats strange is it opens about 8"x8" and will reopen in the same place I close it last. If I expand it to full screen and then close it, it reopens full screen. It will only do those 2 things. If I use half the screen for example, and then close it, it opens as a small window again. It wont remember unless its full screen. All previous versions opened exactly as I closed them, which for my is about 3/4 of the screen used.

[Keith@HPTuners]

Are you using a multi monitor display, or anything unique to your setup?

[realcanuk]

Are you using a multi monitor display, or anything unique to your setup?

Keith,
It behaves the same way on my dual monitor desktop and my normal laptop. On both it only remembers previous size if full screen. If I close it while taking only part of the screen, it reopens as a smaller window near the center.
Both are running windows 10

[Higgs Boson]

To clarify - the min/max override feature was intended only for overriding HPT-set limits in cases where the ECM actually supports higher values.
So if the ECM software was only meant to work with a value of 1.0, even though the data structure may support a value of 2, the ECM may ignore anything above 2.

In other words, I would not adjust the values unless you're absolutely certain that the software supports these (higher or lower) values.

So I am also tuning a 2015 C7 LT1 stroker with a supercharger and it too will not get into boost with a failed MAF.

So the two variables here are 2014 (which worked) vs 2015+ or something to do with 2.2x vs 3.x

Still hitting my head on the wall here, if there is any solution it would be appreciated.

[ony]

I think if you right click on your icon ,propertys you have the choich of what size window it opens in.

[06MonteSS]

here's a shot of the IAT table.. compare view - which is my stock file, and then when I go to Differences view, the columns are all whacked, not at all what they are in Main or Compare views..

Attachment 60103Attachment 60104

so I just downloaded the latest 3.2 version, and this problem still exists...

[Keith@HPTuners]

We're looking to put that fix into 3.4

[normc5]

Will this update support 2016 Chevrolet Cruze 1.4T? A coworker has a loaner and thought I'd copy the file with v3.0 and it would not recognize anything.

I can try again Thursday or Friday if this current update will work. If not can I help getting a copy to someone?

[5_Liter_Eater]

3.2.20, E40, 2005 vette: Alcohol percent is not displaying in the scanner channel list. The channel is there but the value is blank. Thought it may be a problem with my ethanol sensor retrofit but 2.24 displays it properly.

[5_Liter_Eater]

Updated to latest build, 3.2.25 with same behavior.

[schpenxel]

Did you use a 2.24 config or add that channel In 3.2? I know it works in mine, I'll post my channel list in a bit to see if it works then

[5_Liter_Eater]

No my channel list in 3.2 was initially created in 3.0 and was working then. Attached is the channel xml

[5_Liter_Eater]

Also if I open an old 3.0 log in 3.2 it displays properly.

[Keith@HPTuners]

3.2.20, E40, 2005 vette: Alcohol percent is not displaying in the scanner channel list. The channel is there but the value is blank. Thought it may be a problem with my ethanol sensor retrofit but 2.24 displays it properly.

Try logging the parameter alone. See what minimum parameter set you can log that shows the issue.