Page 1 of 10 12345 ... LastLast
Results 1 to 20 of 185

Thread: VCM Scanner 3.2.9+ Serial Wideband Feedback

  1. #1
    HP Tuners Owner Keith@HPTuners's Avatar
    Join Date
    Sep 2002
    Location
    Chicago, IL
    Posts
    6,394

    VCM Scanner 3.2.9+ Serial Wideband Feedback

    Previous thread: http://www.hptuners.com/forum/showth...eband-Feedback

    Serial input should now work for:
    AEM
    Innovate LC-1, LC-2, LM-1, LM-2

    If you have any of these sensors, please test it.

    Please respond with something along the lines of:

    VCM Scanner version #
    Innovate LC-1: Works

    - OR -

    VCM Scanner version #
    Innovate LC-1: Doesn't work
    (provide detailed description as to what exactly isn't working)
    We got this guy Not Sure, ...

  2. #2
    Senior Tuner mowton's Avatar
    Join Date
    Mar 2007
    Location
    Florida
    Posts
    3,773
    OK so I am new to the serial interface...trying my LM-1 (loaded latest firmware) but I add the channel, input to chart and when I connect/log, the channel deignator disappears and no data is recorded...

    I can connect through my serial to USB adapter and program the LM-1 so COM Port 4 where it is connected must be working.

    Thx

    Ed M
    2004 Vette Coupe, LS2, MN6, Vararam, ARH/CATs, Ti's, 4:10, Trickflow 215, 30# SVO, Vette Doctors Cam, Fast 90/90, DD McLeod, DTE Brace, Hurst shifter, Bilsteins etc. 480/430

    ERM Performance Tuning -- Interactive Learning ..from tuning software training to custom tunes
    HP Tuners Dealer- VCM Suite (free 2hr training session with purchase), credits and new Version 2.0 turtorial available
    http://www.ermperformancetuning.com
    http://www.facebook.com/ERMPerformanceTuning

    [email protected]

  3. #3
    HP Tuners Owner Keith@HPTuners's Avatar
    Join Date
    Sep 2002
    Location
    Chicago, IL
    Posts
    6,394
    If it dissapears, the SW is not detecting it correctly... and if you can use innovates software to configure/monitor the device, then it's likely our software that still needs work.

    Remember though, only one software can connect to the device at a time. If you have innovate software connected, vcm scanner won't be able to connect.
    We got this guy Not Sure, ...

  4. #4
    Senior Tuner mowton's Avatar
    Join Date
    Mar 2007
    Location
    Florida
    Posts
    3,773
    I did not have the innovate software running at the time. Went through those steps in the beginning as i was setting up the rs232 to USB drivers. What would you need from me?

    Also.it dawned on me that I won't be able to utilize the serial interface when tune/logging with my Surface Pro 3..
    .only one USB :-(

    Thx

    Ed M
    2004 Vette Coupe, LS2, MN6, Vararam, ARH/CATs, Ti's, 4:10, Trickflow 215, 30# SVO, Vette Doctors Cam, Fast 90/90, DD McLeod, DTE Brace, Hurst shifter, Bilsteins etc. 480/430

    ERM Performance Tuning -- Interactive Learning ..from tuning software training to custom tunes
    HP Tuners Dealer- VCM Suite (free 2hr training session with purchase), credits and new Version 2.0 turtorial available
    http://www.ermperformancetuning.com
    http://www.facebook.com/ERMPerformanceTuning

    [email protected]

  5. #5
    HP Tuners Owner Keith@HPTuners's Avatar
    Join Date
    Sep 2002
    Location
    Chicago, IL
    Posts
    6,394
    Use a USB hub.

    Contact support and open up a ticket, and I can put something in the beta for you to test.
    We got this guy Not Sure, ...

  6. #6
    Senior Tuner mowton's Avatar
    Join Date
    Mar 2007
    Location
    Florida
    Posts
    3,773
    Quote Originally Posted by Keith@HPTuners View Post
    Use a USB hub.

    Contact support and open up a ticket, and I can put something in the beta for you to test.
    Thanks for the Hub advise and email sent...have a good night

    Ed M
    2004 Vette Coupe, LS2, MN6, Vararam, ARH/CATs, Ti's, 4:10, Trickflow 215, 30# SVO, Vette Doctors Cam, Fast 90/90, DD McLeod, DTE Brace, Hurst shifter, Bilsteins etc. 480/430

    ERM Performance Tuning -- Interactive Learning ..from tuning software training to custom tunes
    HP Tuners Dealer- VCM Suite (free 2hr training session with purchase), credits and new Version 2.0 turtorial available
    http://www.ermperformancetuning.com
    http://www.facebook.com/ERMPerformanceTuning

    [email protected]

  7. #7
    Advanced Tuner Montecarlodrag's Avatar
    Join Date
    Nov 2009
    Location
    Pegasus Galaxy
    Posts
    919
    I have 3 of those models, LC-1, LC-2 and LM-2, will test and report back.
    9 sec Montecarlo SS

  8. #8
    Does a usb 1.0 to serial cable work for this? I just ordered one and realized after I did that it was a 1.0 usb and not the normal 2.0. i dont think it would matter but just want to check. after i get it ill report back on aem for ya.

  9. #9
    Moderator
    Join Date
    Mar 2014
    Location
    Raleigh, NC
    Posts
    6,347
    as long as it creates a com port that follows normal com protocols it should work

  10. #10
    Potential Tuner
    Join Date
    Feb 2016
    Posts
    7
    innovate LC-2 not working, reads 493.0000 lamda when i read it through the logworks software it reads 1.5 lamda both times key on engine off.

  11. #11
    HP Tuners Owner Keith@HPTuners's Avatar
    Join Date
    Sep 2002
    Location
    Chicago, IL
    Posts
    6,394
    Quote Originally Posted by Acgrading View Post
    innovate LC-2 not working, reads 493.0000 lamda when i read it through the logworks software it reads 1.5 lamda both times key on engine off.
    What version of VCM Scanner?
    We got this guy Not Sure, ...

  12. #12
    Potential Tuner
    Join Date
    Feb 2013
    Posts
    8
    Quote Originally Posted by Acgrading View Post
    innovate LC-2 not working, reads 493.0000 lamda when i read it through the logworks software it reads 1.5 lamda both times key on engine off.
    Same for me too innovate LC2 on version 3.0.71

  13. #13
    HP Tuners Owner Keith@HPTuners's Avatar
    Join Date
    Sep 2002
    Location
    Chicago, IL
    Posts
    6,394
    If you are having issues, you'll have to open up support tickets so we can trouble shoot what's going on.
    We got this guy Not Sure, ...

  14. #14
    HP Tuners Owner Keith@HPTuners's Avatar
    Join Date
    Sep 2002
    Location
    Chicago, IL
    Posts
    6,394
    You guys will need to get tomorrows beta (April 6, 2016) and try again, and report your debug.dat files to support for analysis.
    We got this guy Not Sure, ...

  15. #15
    Potential Tuner
    Join Date
    Feb 2016
    Posts
    7
    Quote Originally Posted by Keith@HPTuners View Post
    You guys will need to get tomorrows beta (April 6, 2016) and try again, and report your debug.dat files to support for analysis.
    thanks Keith i am using 3.0.72 I will try again tomorrow

  16. #16
    Senior Tuner mowton's Avatar
    Join Date
    Mar 2007
    Location
    Florida
    Posts
    3,773
    On the road today....will try out .73 and beta .213 tonight when i get home.

    I tried to log with it today on a Tahoe and it wouldnt display the CHART data while logging, but once I stopped and saved the log and then reopened it, the data was displayed? I'll have to check it out when I get home as well.

    Ed M
    Last edited by mowton; 04-07-2016 at 08:39 AM. Reason: Wrote graph in first post should have said CHART...
    2004 Vette Coupe, LS2, MN6, Vararam, ARH/CATs, Ti's, 4:10, Trickflow 215, 30# SVO, Vette Doctors Cam, Fast 90/90, DD McLeod, DTE Brace, Hurst shifter, Bilsteins etc. 480/430

    ERM Performance Tuning -- Interactive Learning ..from tuning software training to custom tunes
    HP Tuners Dealer- VCM Suite (free 2hr training session with purchase), credits and new Version 2.0 turtorial available
    http://www.ermperformancetuning.com
    http://www.facebook.com/ERMPerformanceTuning

    [email protected]

  17. #17
    We email support for the beta correct? And does it have to be a serial to usb or will just a serial work and Hp recognize it? Sub is coming but I have a serial port and cable laying around

  18. #18
    Senior Tuner mowton's Avatar
    Join Date
    Mar 2007
    Location
    Florida
    Posts
    3,773
    Keith,

    Tried the LM-1 Serial Interface via Beta 3.1.216 and Version 3.0.75 with the same results. Sent a followup email to support (ticket #32709) with debug.dat and information fies.

    I was able to intiate logging and see the chart plotting using the Beta 216 on my 04 vette today which yesterday, on a 07 Tahoe I couldn't with Beta 213...Not sure if that helps or not.

    Ed M
    2004 Vette Coupe, LS2, MN6, Vararam, ARH/CATs, Ti's, 4:10, Trickflow 215, 30# SVO, Vette Doctors Cam, Fast 90/90, DD McLeod, DTE Brace, Hurst shifter, Bilsteins etc. 480/430

    ERM Performance Tuning -- Interactive Learning ..from tuning software training to custom tunes
    HP Tuners Dealer- VCM Suite (free 2hr training session with purchase), credits and new Version 2.0 turtorial available
    http://www.ermperformancetuning.com
    http://www.facebook.com/ERMPerformanceTuning

    [email protected]

  19. #19
    Tuner in Training
    Join Date
    Jul 2008
    Posts
    15
    Aem is working with today's build

  20. #20
    Potential Tuner
    Join Date
    Jan 2016
    Posts
    5

    Is this for the aem 30-4110 wideband

    Quote Originally Posted by Alan 956 View Post
    Aem is working with today's build