Page 6 of 10 FirstFirst ... 2345678910 LastLast
Results 101 to 120 of 185

Thread: VCM Scanner 3.2.9+ Serial Wideband Feedback

  1. #101
    Advanced Tuner
    Join Date
    Dec 2005
    Location
    Posts
    599
    Makes sense.

  2. #102
    VCM Scanner version #397
    Innovate MTX-L: Works

  3. #103
    upon further testing it works fine but if i stop and restart the log the wideband will not log anymore. I have to close and reopen the program to get it to work again. This happens every time.

  4. #104
    Tuner in Training
    Join Date
    Sep 2015
    Posts
    26
    One question to everyone. Are you using the serial output of your LM-1/2 or the USB output. I ask because the USB output uses the SP2 serial protocol and I believe that is what is being implemented. I don't have a vehicle to test it on atm but I plan to in the coming week. I might just go out to my DD and leave the LM-2 in free air to see if I get any reading over the USB interface. I'm hoping I do.

  5. #105
    Quote Originally Posted by Maglin View Post
    One question to everyone. Are you using the serial output of your LM-1/2 or the USB output. I ask because the USB output uses the SP2 serial protocol and I believe that is what is being implemented. I don't have a vehicle to test it on atm but I plan to in the coming week. I might just go out to my DD and leave the LM-2 in free air to see if I get any reading over the USB interface. I'm hoping I do.
    Serial with serial to usb converter.
    MTX doesn't have a usb out.

  6. #106
    Senior Tuner
    Join Date
    May 2016
    Posts
    1,134
    Quote Originally Posted by dr.mike View Post
    Unfortunately, the only way to change the fuel constant ( from 14.7 ) is via the CANBus API.

    I am pretty sure that they thought that nobody was going to use the serial output.

    If you have the MPVI Pro, you can use the 0-5v analog interface. It is actually better than the serial. It has gound offset compensation. And, full speed data.

    If you want to send it to me, I can give it the OBDII re-flash and change the fuel constant to 14.2
    I have been using serial on my MPVI Pro with an AEM 30-0310 thinking it would be faster and more accurate. So you recommend switching back to the old way?

  7. #107
    Moderator
    Join Date
    Mar 2014
    Location
    Raleigh, NC
    Posts
    6,347
    I'd get dr.mike to re-flash it for you then just run it over the CAN bus. Then it's faster than 0-5V or serial.

  8. #108
    Senior Tuner
    Join Date
    May 2016
    Posts
    1,134
    Quote Originally Posted by schpenxel View Post
    I'd get dr.mike to re-flash it for you then just run it over the CAN bus. Then it's faster than 0-5V or serial.
    It's a portable setup used to tune multiple vehicles.

  9. #109
    Moderator
    Join Date
    Mar 2014
    Location
    Raleigh, NC
    Posts
    6,347
    And? Pretty sure those vehicles have an OBD port.

  10. #110
    Senior Tuner
    Join Date
    May 2016
    Posts
    1,134
    So I could wire it into device OBD adapter and not have to wire it into each car I'm logging?

  11. #111
    Moderator
    Join Date
    Mar 2014
    Location
    Raleigh, NC
    Posts
    6,347
    Can be wired to one of these so you can just plug it into OBD port then plug HPT into it

    https://www.amazon.com/gp/product/B0...?ie=UTF8&psc=1

    The only problem I can think of is on pre CAN vehicles you have to add a resistor and CAN vehicles don't need that.. so that'd be something that would change depending on vehicle

  12. #112
    Moderator
    Join Date
    Mar 2014
    Location
    Raleigh, NC
    Posts
    6,347
    I'm waiting on my new WB to get here. Should be hereTuesday.

  13. #113
    Tuner
    Join Date
    Jun 2006
    Location
    Manchester, NJ
    Posts
    59
    I have innovate LC-2

    it is working!
    Last edited by DaFlyinSkwirl; 06-21-2016 at 09:24 PM. Reason: working

  14. #114
    Tuner in Training
    Join Date
    Dec 2011
    Posts
    20
    This is what I'm running. The voltage reading at the end of my male/female connector is right in line with the stated chart. Still trying to figure out how to get it to communicate with scanner. I'm using a DB9 to USB converter. My laptop recognizes the port and converter, but I've got nothing in the scanner. I'll post an update once it's figured out. Hoping to add another Wide-band option to the mix.


    http://prosportgauges.com/wideband-a...ratio-kit.aspx
    http://prosportgauges.com/instructio...alwideband.pdf

  15. #115
    Any progress on the ECM AFM1500?

  16. #116
    Advanced Tuner
    Join Date
    May 2016
    Location
    Adelaide, Australia
    Posts
    246
    Can zeitronix zt2 serial support please be added.
    Thanks
    Ben

  17. #117
    HP Tuners Owner Keith@HPTuners's Avatar
    Join Date
    Sep 2002
    Location
    Chicago, IL
    Posts
    6,394
    Quote Originally Posted by Ben C View Post
    Can zeitronix zt2 serial support please be added.
    Thanks
    Ben
    Do you have a link to the protocol?
    We got this guy Not Sure, ...

  18. #118
    Advanced Tuner
    Join Date
    May 2016
    Location
    Adelaide, Australia
    Posts
    246
    Quote Originally Posted by Keith@HPTuners View Post
    Do you have a link to the protocol?
    This should help
    tmp_10191-Zeitronix Protocol-1949359585.txt
    Attached Files Attached Files
    Last edited by Ben C; 06-23-2016 at 06:50 PM.

  19. #119
    Tuner
    Join Date
    Oct 2011
    Location
    Australia
    Posts
    175
    Could serial support for Techedge 2J2/9 be added please. Links below have alot of info not sure if the protocol info is in there as I don't know what I'm looking for. I will contact Techedge to ask them directly for protocol info. I have sent a request to HPTuners support also.

    http://wbo2.com/2j/default.htm

    http://wbo2.com/sw/logtech.htm

  20. #120
    Tuner in Training
    Join Date
    Jun 2007
    Posts
    19
    VCM Scanner version: 3.2.24
    Innovate LC-2 with Bosch 4.2 Sensor: Works great!