can anyody pinpoint were i can find the channel for "injector duty cycle"
can anyody pinpoint were i can find the channel for "injector duty cycle"
Im having the same issue with any controller i plug into.
Injector Duty Cycle is a math parameter. It is virtual. You cannot add virtual parameters to the Channel list.
You can however plot them in gauges/charts/graphs.
We got this guy Not Sure, ...
ahh makes sense! thanks!
still don't understand how to set up injector duty cycle please help
Guys this isn't hard
Where do you want it? In a chart or what? You CANNOT add it to the "channel" window.
Go to chart vs. time, right click, select chart layout.
Click on the button with the plus that will say "Add series" when you hover your cursor over it. This adds a new PID to the chart
Beside the word "parameter" it should say "click to insert or change". Click on that.
Type in "duty" and hit the gear with the little green check box at the top. That will filter out all PID that you can't use and only show you valid ones.
Double click on "Injector duty cycle [Ratio]"
Change color, min, max to your liking and X out of the Chart display editor
And you are done
Post a log and tune if you want help
VCM Suite V3+ GETTING STARTED THREADS / HOW TO's
Tuner by night
CPX Tuning
2005 Corvette, M6
ECS 1500 Supercharger
AlkyControl Meth, Monster LT1-S Twin, NT05R's
ID1000's, 220/240, .598/.598, 118 from Cam Motion
2007 Escalade, A6
Stock
2004 Vette Coupe, LS2, MN6, Vararam, ARH/CATs, Ti's, 4:10, Trickflow 215, 30# SVO, Vette Doctors Cam, Fast 90/90, DD McLeod, DTE Brace, Hurst shifter, Bilsteins etc. 480/430
ERM Performance Tuning -- Interactive Learning ..from tuning software training to custom tunes
HP Tuners Dealer- VCM Suite (free 2hr training session with purchase), credits and new Version 2.0 turtorial available
http://www.ermperformancetuning.com
http://www.facebook.com/ERMPerformanceTuning
[email protected]
I forget I've been using it a bit longer than most
Guys my IDC shows when logging but when I save the log to review it later it shown nothing,IDC is blank..when I send my log to another person he can see IDC in the log!!weird..can anybody help?
Post a log
Are you on today's release of HPT?
I am on 3.0.19..I will post a log..
how do i post a log here?i am sorry but i am confused..
Start a post. Go to bottom right if post box and click ADVANCED. Go to attachments and follow the instructions a box will appear that Saya add file and browse. Hit browse, fun your log and double click file. Hit upload and file box will appear at the lower left of the open window. Hit insert online and file name should be in rhe attachment area. Close theis windo and submit the post. Did thus from my phone and memory so may be a bit disjointed.
Ed M
2004 Vette Coupe, LS2, MN6, Vararam, ARH/CATs, Ti's, 4:10, Trickflow 215, 30# SVO, Vette Doctors Cam, Fast 90/90, DD McLeod, DTE Brace, Hurst shifter, Bilsteins etc. 480/430
ERM Performance Tuning -- Interactive Learning ..from tuning software training to custom tunes
HP Tuners Dealer- VCM Suite (free 2hr training session with purchase), credits and new Version 2.0 turtorial available
http://www.ermperformancetuning.com
http://www.facebook.com/ERMPerformanceTuning
[email protected]
So it doesn't open the first time you open the log, but if you re-open it, it works. We'll look into it.
We got this guy Not Sure, ...
Keith the weird thing is that when I log I can see the IDC working but when I save the log to review it later,it's blank..emailed my log to a friend and he could see IDC..why can't I see my IDC after saving my log?
Keith found the problem...when I save it on my desk top and open the log the IDC isn't working..when I open my scanner,and open my log file from there it works!!