VCM Scanner 2.25 Beta Now Available

[Pector55]

I sent in a request for the 2.25 Beta. It was like Christmas getting my tuner for the Challenger but then I found I have to wait in line for a beta version of the software to use it so it turned into more of a Christmas Vacation. Shitter's full! ;-)

[schpenxel]

New beta up?

[Keith@HPTuners]

yes.

[schpenxel]

No dice

(same issue)

[Keith@HPTuners]

Build 2616?

Post your log, layout, and exact steps you use to duplicate the issue.

[schpenxel]

Build 2616?

Post your log, layout, and exact steps you use to duplicate the issue.

Yes, 2616 K, log/layout/video coming up in a bit. I'll confirm just to be sure in a second

[schpenxel]

Here ya go. Video is a little jumpy but should work well enough to see what's going on

esc 2.25, 2.hpl

Beta Layout.Layout.xml

https://youtu.be/R7G-4bDBYR0

[Keith@HPTuners]

Ok, new beta up. Try this one with the filters.

For reference, if the filter isn't supported (or malformed), it will always pass as true.

[schpenxel]

I haven't been able to break it again.. I'll keep trying :lol:

Thanks for taking care of it!

Now I'll begin begging for user defined variables

[Sparkey]

Sparkey, you must have a different AEM wideband to mine (30-4100) as that formulae is correct for me (AEM quotes V * 2 + 10.0 but that is the same). My only issue is that I need to compensate for the ground difference.

This AEM is a 30-5130

V/.5+10 is the same as V*2+10, mathematically.

I am aware of the conversion but I thank you for bringing it to attention just in case.



The transfer for this particular wideband is 2.375(Volts)+7.3125 I don't care if it is added specifically as I am sure there are just too many WB to accommodate all, but 'User Defined' transfer functions would fill that gap.

[schpenxel]

You can change the output function on a lot of WB's which will obviously make it easier to get a WB going on 2.25 if yours isn't currently supported

[schpenxel]

Should the new scanner be recording any quicker than the old one? A 1 hour log got about 300K frames (when exported) for me this morning. I don't remember 2.24 ever getting data at that rate. Or maybe I'm just logging less stuff now or something.

[Keith@HPTuners]

2.25 supports broadcast parameters, which will log faster, and allow requested parameters to log faster as well.

2.24 does not support that feature.

[schpenxel]

Gotcha. This was on an E38. I'll try on an E40 maybe tomorrow.. it always has gotten 20K frames/hour so I'll be able to compare better on it

[schpenxel]

Small bugs:

-STFT B1 reports 100% all the time on the attached tune. Seems like this was fixed in an earlier release but I'm not 100% sure on that.
-The red dots that (presumably) indicate a particular graph has a filter applied don't seem to turn on/off correctly

esc 2.25, 2.hpl

Dots.JPG

[Keith@HPTuners]

Attach your channel config please and I'll test on the bench.

Eventually I'd like to add the ability to extract a channel config from a log.

[schpenxel]

Here she be:

(this wasn't on a Corvette, that was just what I named it apparently)

Corvette Channel Config.Channels.xml

[Keith@HPTuners]

new beta up that should fix the scanning issue with the misreported values.

This should fix a lot of misreported value issues.

[schpenxel]

Good deal. Will give it a go later. Apparently I need to do some work at the day job.

[schpenxel]

Should it show up correctly now when looking at old logs, or is it a matter of it now recording properly when recording new logs?

(i.e. my old logs look the same)