Results 1 to 10 of 10

Thread: logging VE wb afr, VE afr error

  1. #1

    logging VE wb afr, VE afr error

    histograms don't go past 2800rpm.

    any particular reason why?
    i just installed my plx, and did some logging with the new wb with my HPT.
    the other histograms cover all the rpm i hit, but the above mentioned do not.

    the install went well. i tested it before i did the runs, and all was fine.

    thanks in advance.

    PS: oh! right clicked on the main table, insert, wideband, Plx. it seemed fine when i tested it.

  2. #2
    HP Tuners Support
    (foff667)
    Bill@HPTuners's Avatar
    Join Date
    Jun 2004
    Location
    Hailing from Parts Unknown
    Posts
    28,247
    Please post your .hpl & cooresponding .cfg file, without these things its impossible to help.
    It doesn't have to be perfect, it just needs to be done in two weeks...

    A wise man once said "google it"

  3. #3
    thanks! and sorry!

    here is the last log, short, but a log.
    and the config file.

    again, thanks!

  4. #4
    HP Tuners Support
    (foff667)
    Bill@HPTuners's Avatar
    Join Date
    Jun 2004
    Location
    Hailing from Parts Unknown
    Posts
    28,247
    Quote Originally Posted by jegten
    thanks! and sorry!

    here is the last log, short, but a log.
    and the config file.

    again, thanks!
    You have a cell count filter of 30, unless you have 30 in a cell it won't show.
    It doesn't have to be perfect, it just needs to be done in two weeks...

    A wise man once said "google it"

  5. #5
    should i go for a much smaller number?
    i had 0 there before i did the run.

    thanks!

  6. #6
    man!
    that was easy!
    thank, Bill! as always!

    but, since i am doing the afr error, i should probably have some count to be able to use a nice average, right?

  7. #7
    HP Tuners Support
    (foff667)
    Bill@HPTuners's Avatar
    Join Date
    Jun 2004
    Location
    Hailing from Parts Unknown
    Posts
    28,247
    I wouldn't change my cell count if I were you, what I would do, however, is lower my bytes used to 24 or less so I get 10fps hits.

    Currently your logging 31 bytes of data and only getting 5fps hits meaning 1/2 as much data is being logged in the same amount of time as a person only logging 24 bytes.
    It doesn't have to be perfect, it just needs to be done in two weeks...

    A wise man once said "google it"

  8. #8
    thanks!
    i will do that. actually, how do i change that? i can't seem to find how to change. sorry!
    also, what afr do i want to be commanded when logging?
    right now i have 14.68 hi res.
    Last edited by jegten; 01-08-2008 at 02:34 PM.

  9. #9
    HP Tuners Support
    (foff667)
    Bill@HPTuners's Avatar
    Join Date
    Jun 2004
    Location
    Hailing from Parts Unknown
    Posts
    28,247
    http://www.hptuners.com/forum/showthread.php?t=15989

    Changing the cell count is done here where it says cell hits required

    It doesn't have to be perfect, it just needs to be done in two weeks...

    A wise man once said "google it"

  10. #10
    thanks, bill!
    i will delete my lo res pid and other ones, so that i can get the bytes needed.
    thanks for the screen shot. you had already helped me to figure out where that was earlier. thanks!
    i will have to go through the guide again, since i am commanding a 14.68 afr for transition. that's what i thought i read, putting 1s across that table open loop eq ratio.

    again, thanks!
    Last edited by jegten; 01-08-2008 at 10:26 PM.