HPT Not working

[Phil'sC5Vette]

I was just about to head to a friends house to shut off a few codes, and wanted to put load a new tune in my car.

I plugged the system in and turned the car to run, and when I tried to upload the tune HTP tells me interface was found, but no veicle power was found.

So, I checked every connection 3 plus times, the car is on run, and I keep getting the same pop up.

My laptop is plugged in to the outlet so it's charged.

I justed the car to make sure it work and it started up after sitting for two week.

I tried to run scanner and got the same information.

What's the deal?

[Bill@HPTuners]

check for blown fuses. Usually if it detects the interface but no vehicle power that is the culprit.

[Phil'sC5Vette]

ZI just unpluged the system from the computer and pushed the record button on my MPVI with the car on run, and the record is not lighting up.

I am plugged into the ODB II, and it looks like the MPVI isnt getting power.

[Phil'sC5Vette]

which fuse am I looking for ?

[Bill@HPTuners]

ZI just unpluged the system from the computer and pushed the record button on my MPVI with the car on run, and the record is not lighting up.

I am plugged into the ODB II, and it looks like the MPVI isnt getting power.

Instructions for using standalone logging are in the help file as well as a flash demo which runs you through step by step. If you do not follow the instructions standalone datalogging will NOT work.

[Bill@HPTuners]

which fuse am I looking for ?

probably the cig lighter

[Phil'sC5Vette]

I pulled all the viewible fuses and none are blown

The cigarette lighter works. First time I used it lol

[Phil'sC5Vette]

does the MVPI have a fuse ?

The car is running and no codes, but the MPVI isnt working on the car side

I hold down the record button and it doesnt do anything

[Bill@HPTuners]

does the MVPI have a fuse ?

no

The car is running and no codes, but the MPVI isnt working on the car side

so you can read the codes with the scanner? can you retrieve a vcm suite infolog?

I hold down the record button and it doesnt do anything

you need to configure the standalone datalogger for it to work as previously stated. The demo in the help file www.hptuners.com/help runs you through step by step how to use it.

[Phil'sC5Vette]

Nope, nothing comes over when I open the scanner nd try to log.

Also the MPVI has been configured for stand along. I dont use the lap top for logging

[Bill@HPTuners]

Also the MPVI has been configured for stand along. I dont use the lap top for logging

So you've reconfigured it for your friends car then?

When you hook the hardware to your obd2 port but NOT your laptop does the green power light come on?

[Phil'sC5Vette]

when I only hook up the MPVI to the OBD, NO the green light does not come on. It DOES when I plug it into the laptop.

No I did not program the MPVI for my friends car. I wanted to change the tune in my car and never made it to my friends house

Here are the codes that came up in the car from the DTC

bcm-
bo502
bo507
bo2482

ipc
u1255

ao-ldcm
2284
u1064
u1096

ao rdcm
2285
1064

rfa
u1096
1064
1016

all the lights and everything work.
could the codes be from pulling the fuses ? Im not sure how long they have been in there for.

[Phil'sC5Vette]

Looks like all the codes were history codes.

Im going to take the car for a quick run and see if I get new ones

[Phil'sC5Vette]

Bill,
After a quick 15 mintue drive, no codes came up. I plugged in the MPVI pro, and when I pushed in the record button, nothing happened

[Phil'sC5Vette]

If you want tp PM me your number, Ill give you a call

[Keith@HPTuners]

When you plug the interface into the vehicle, the power light should come on, if not it indicates no obd2 port power, bad obd cable, or bad interface.

[Phil'sC5Vette]

When you plug the interface into the vehicle, the power light should come on, if not it indicates no obd2 port power, bad obd cable, or bad interface.

nope, it only comes on when I plug it into the computer
what's the next step, the unit is about 10 months old

[Keith@HPTuners]

Plug it into another vehicle, if the power light comes on, you know its your obd2 fuse.

[Phil'sC5Vette]

bingo !

Plugged into my wife's GM unlander and the light came on.

Do you know which fuse it would be in a Y2K C5 ?
I checked them and they all looked fine

[Keith@HPTuners]

I do not, sorry.