I did not have any luck with the Repository.
Would like to have a look at both a manual and auto trans calibration for a 2018 Ecoboost Mustang. Stock Reads.
Thanks in Advance.
Type: Posts; User: Mobile Chassis Dyno
I did not have any luck with the Repository.
Would like to have a look at both a manual and auto trans calibration for a 2018 Ecoboost Mustang. Stock Reads.
Thanks in Advance.
Can we read the pcm without the break out cable or is it needed to read the pcm as well?
Has anyone had luck using 3.0 to log the necessary data for Predicted Throttle Angle and Effective area? I have a 2015 GT that is going to be left with me for a few days and I want to spend time to...
Vin number in the dash matches the vin read out in the ecm. So I am sure its a 2004.
HP Tuners says its a NGC3. I bought credits and licensed it based on that is supposed to be a NGC3. Email with tunes and vcm log sent to support. Please advise if something can be done or if I need...
Keith,
ORG - Original Read.
DTM - Scaled Injectors only to start.
VCM log attached.
I have a bigger problem. I have spent the last 3 hours trying to get the car to flash. Fails when...
Any reason why 2005 SRT 4 offers unlimited model/year support and not 2004?
Seems like the licensing changes from time to time with beta updates.
I want to license all 2016 corvette. Are single licensing the only thing available at this time?
The 97 OS's that I have looked at offer a 2 Bar OS.
Wondering if it is possible to add the Variable Cam tables for the attached tune file. The only VCT adjustments are to determine which VE table to use based on cam positioning. We are wanting to be...
Are we able to disable ANN and Speed Density and run them off the maf? Being that ANN is enabled. Is the maf even used for fuel and load calculations?
Problem fixed. Was using a 2014 GT that I tuned as a compare file that I tuned. Had to do some of the changes manually instead of using the copy feature under the compare tab. Car is staying in...
I have a 2013 GT that will go from Closed Loop back to Open Loop and stay there after 2 minutes of run time. Car can be idling or cruising down the road. After about 2 minutes the car will go to O/L...
Tuning on a truck that starts to cut throttle and of course boost when trying to get over 17 psi. Looks like I may be losing rail pressure when this happens. I have turned up every torque and boost...
OS - 12216215
2002 Silverado.
4L60E to Manual Trans swap.
Did a bench tune for the customer. Set the trans from 4L60E to Manual. Customer is getting a no start. He is telling me the truck...
Got the the VSS to work and no more wrench light.
Update,
Wrenches under part throttle above 3500 rpms regards of TPS and gear.
Tuning on a 07 Vic with a TR3650 swap. Speedo decided to stop working after the first dyno pull. Car is now shutting down at 3600 rpms under WOT and throwing a P2105 and Wrench light. Is the lack of...
Email Sent.
Trying to compare and VCM Editor keeps crashing when trying to compare tunes for the same car.
Just downloaded the latest beta and I am still getting the same message.
Unable to open file. You are not authorized
Any idea why I would be getting this message on a tune file that I licensed?
Software version - 2.25.2341
Original Read Attached
Thank you 06300CSRT8 for the info. Going to have a look at the car again Friday night hopefully. I am told the car should make around 16 psi. Car was previously owned by a Dodge Dealer and went under...
Car in question came to me with stalling issues and a extremely sensitive throttle response. Car is not safe to drive as it will go from little vacuum to 160 or more kpa and blistering the tires with...
What were your coolant temps during the pulls? I have found these cars tend to take a bit more timing with coolant temps in the 180's thanks to a cooler T Stat.