Ok so I know a bit to get me by on na and nitrous from over the last 7 years but now Im going turbo.
My setup is 6.0 ly6 with aftermarket vvt cam. The OS is a '10 e67 out of a '10 Colorado with a...
Type: Posts; User: tiresmokinV8
Ok so I know a bit to get me by on na and nitrous from over the last 7 years but now Im going turbo.
My setup is 6.0 ly6 with aftermarket vvt cam. The OS is a '10 e67 out of a '10 Colorado with a...
I know but I dont know what it could be?
Truck sputters at a certain mid throttle and wot then after a bit it drives just fine. Also does it sometimes after driving fine for a while and wont go away until sometimes turning the truck off...
Ill do that. The whole lsx conversion harness is made by Current Performance, I sent it back over winter to have it converted from manual to auto harness and use a t42 tcm. Ill check the pins and...
Thanks. Ive had 3 80e's in the truck before finding a good one, this one is a brand new Jakes 80e and all 3 had this code pop up. Trans seems to function just fine and it ussually pops up as soon as...
[] P0961 - Pressure Control (PC) Solenoid A System Performance (Old) (History) (Current) (Immature)
[] P2764 - Torque Converter Clutch Pressure Control Solenoid Control Circuit Low (SES) (Old)...
I have a '10 e67 and t42 tcm and would love to be able to keep my convertor locked on my 4l80e like the older computers can.
I have a ly6 6.0 and a 4l80e run by a '10 e67 and t42 "colorado base tune", Im pretty sure that I read that they came out with a fix for the convertor remaining locked even at 0%tps which is what I...
It doesn't have a problem upshifting or down shift though. it just at idle it seems like the convertor is still trying to spin the trans. I put up a link to my discussion with Jake and CircleD on my...
'10 e67 with Colorado base tune and t42 tcm. TCM was tuned by Currentperformance as was the wiring. Problem is reverse just drags the engine down to where I cant hold the brakes while in reverse or...
Ive tuned it pretty darn good on my own but still would like it professionally dyno tuned.
I just added a tcm inline to solve my vss problems but now since theres no auto trans a few dtcs popped up and I was only able to find and turn off po700 the rest arent in my dtc list in hpt.
...
Well I have been running with the 158mph vss for the last 4000 miles without a problem but my tuner wouldnt tune it like that since he feels that with the ecu thinking its going that fast no matter...
Havent taken it out just tried it with the rear wheels in the air. Its raining out so the truck wont leave the garage.
Thats how mine was since I did the swap but my ecu, maybe base tune, wouldnt accept the trans type manual setting. It didnt change anything. Now with a tcm inline it the ecu reads the vss fine but...
Are you guys still running a tcm inline between the t56 and ecu??? I wasnt but this manual setting didnt fix my 158 issue so I had my wiring harness guy build me a pigtail harness to add a tcm inline...
So is there a special procedure to get this to work? On my '10 colorado e67 I set it manual and write cal but it still reads 158mph at all times.
Where would that be? I cant find anything for a vss signal other then trans outputshaft rpm.
reptos, Speedometer works and always has once I switched it to reptos after doing the swap last year. But the scanner would read 158mph and not allow me to do a crank relearn. Now that we can switch...
Well we should have a fix for this now that we can change trans setting to manual. I did that but nothings changed, Im wondering if its because my vss hi and low are wired into pins 66/67 where they...
Anyone know what pins to hook the vss hi and low to on a '10 Colorado 5.3 e67? Current performance has mine wired into pins 66 and 67 which is where they are for this e67 ecu on a manual cts-v. Would...
Has anyone else had a problem with crank relearn with these setups? My truck is at the tuners but they didnt want to tune it with the vvt unless the crank relearn was working. They said theyve tried...
Dfco and cruise still doesnt work. Now that the ecu is set for manual do I need to supply 12v at the cpp pin? Just looking at the manual pinout for a cts-v using this ecu.
Wow I feel like such a tard. It took Bill emailing me back saying it looks like I already have the latest along with me posting the version number in my last post for it to "click". I just bought a...
Emailed Bill, Looked at my help about and mine is version 2.23.681?? I got it last July 26th.