Search:

Type: Posts; User: 262

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    2,482

    zero the shift times. Reduce force motor a little...

    zero the shift times. Reduce force motor a little more. Make sure the part throttle 100% cell matches the WOT table. Then scan current gear. If it commands the shift and doesnt make the shift its...
  2. Replies
    5
    Views
    3,382

    Thanks again for the beta on a saturday!

    Thanks again for the beta on a saturday!
  3. Replies
    0
    Views
    990

    RPM Control method type

    Is there any way for HPT to look into being able to have selectable RPM limiter methods on the GEN3 OS's like the later model GEN4's have instead of being hard coded to a fuel cut only? Trying to...
  4. Replies
    23
    Views
    10,652

    If you have the shift showing up as commanded and...

    If you have the shift showing up as commanded and it does not happen then something is hurt inside the trans. period. end of story. It may sound harsh but do not beat your head against the wall...
  5. Replies
    14
    Views
    5,758

    Short terms with the file as is with brand new...

    Short terms with the file as is with brand new o2's and confirmed no leaks bounce betwee -3 and +4 and I chase back and forth trying to get them any closer.

    I noticed when in OL that anything...
  6. Replies
    14
    Views
    5,758

    Too many damn numbers to remember and partially...

    Too many damn numbers to remember and partially ratarded 379-397 none the less its a moot point in this controller.
  7. Replies
    14
    Views
    5,758

    What about the tip-in issues?

    What about the tip-in issues?
  8. Replies
    14
    Views
    5,758

    Havent found many OS's that it matters and a...

    Havent found many OS's that it matters and a whopping 14ci difference really isnt a make or break it deal here.

    When the Maf is enabled it is wanting just a little more than what is programmed for...
  9. Replies
    23
    Views
    20,139

    BTR uses the same spring that he has always used....

    BTR uses the same spring that he has always used.

    Now the company who made the springs for patriot is the other leading manufacturer. Now mind you there are only lets say 3 major producers then...
  10. Replies
    14
    Views
    5,758

    ZR1 map sensor the "2525" red label

    ZR1 map sensor the "2525" red label
  11. Replies
    23
    Views
    20,139

    Brian Tooley started TEA and has since left after...

    Brian Tooley started TEA and has since left after summit bought tfs who bought tea and has nothing to do with Marty from Patriot of any of Patriots old products.

    The BTR springs are made by...
  12. Replies
    14
    Views
    5,758

    2010 Camaro 2.5bar OS Whipple driveability issues

    Ever since we did the 2.5 Custom OS on this car it has been nothing but an absolute headache to get the idle correct and get rid of some tip-in bucking.

    Quick run down
    2010 camaro Auto
    379 CI...
  13. Replies
    44
    Views
    42,875

    Bad TPS sensor. Have seen many of them do this...

    Bad TPS sensor. Have seen many of them do this now. If your TPS voltage is good yet it will still read a % value toss that sensor away and start with a new one.
  14. Replies
    13
    Views
    4,826

    How far from stock is the knock sensor settings?

    How far from stock is the knock sensor settings?
  15. Replies
    9
    Views
    5,300

    In a sense that cam is not all that big... it is...

    In a sense that cam is not all that big... it is possible to get 14.7 but should really consider using terms on lambda and taking into account you EOIT and overlap when looking at idle and cruise...
  16. Replies
    9
    Views
    5,300

    sounds like a RAF issues or might need timing...

    sounds like a RAF issues or might need timing tweaked on cranking.
  17. Thread: Opinions On Tune

    by 262
    Replies
    12
    Views
    4,693

    Startup airflow seems to need a little tweak. ...

    Startup airflow seems to need a little tweak.

    Your crossover from low to high maf do not match.

    misfires are tuned off completely.

    Is this tune scaled? Cause fuel injector size is smaller...
  18. Replies
    14
    Views
    6,689

    I with you ed, prolly another lemming in the...

    I with you ed, prolly another lemming in the works.



    :cheers:
  19. Replies
    17
    Views
    11,089

    Walter, when you scale a tune you lose resolution...

    Walter, when you scale a tune you lose resolution to gain range. You have it backwards.
  20. Replies
    4
    Views
    3,137

    What your seeing with your Vig is normal. A...

    What your seeing with your Vig is normal. A torque converters job is to multiple torque. Now if it stops doing that you get the sense of "blowing" through it. Now if the torque ratio drops below 1:1...
  21. First of all do you even know what your max line...

    First of all do you even know what your max line pressure is now?

    Second what other parts did you use? What servos? What band?

    You would need to get in and adjust the EPC table itself then...
  22. Replies
    9
    Views
    4,278

    Pm replied. I think we are on the same page after...

    Pm replied. I think we are on the same page after all
  23. Replies
    9
    Views
    4,278

    As you can see between the two tunes, the PE is...

    As you can see between the two tunes, the PE is not hacked. The MAF and VVE are actually adjusted for what your car needs. There is some TM left along with line pressure adjustments.
  24. Replies
    9
    Views
    4,278

    If you compare your "tune" to the stock file you...

    If you compare your "tune" to the stock file you will see there was hardly anything done.

    VVE and MAF are still stock only the PE was raped. Timing was just increased across the board. The trans...
  25. Thread: Cruze tuning?

    by 262
    Replies
    1
    Views
    1,928

    Cruze tuning?

    Is there support yet?
Results 1 to 25 of 65
Page 1 of 3 1 2 3