Search:

Type: Posts; User: Darin Morgan

Search: Search took 0.00 seconds.

  1. Had this happen twice. Once it trashed the TCM...

    Had this happen twice. Once it trashed the TCM and the dealer could not re-flash. The other time I just left the battery disconnected for 48 hours and it came back. Good luck.
  2. Replies
    5
    Views
    3,675

    I was still fighting the idle issue a bit even...

    I was still fighting the idle issue a bit even after getting the injectors somewhat dialed in. I finally " fixed" the issue by tuning it hybrid VE/MAF. Tune the VE up to 1500 and let the MAF take...
  3. Replies
    5
    Views
    3,675

    Your right, Its a huge pain in the ass but it...

    Your right, Its a huge pain in the ass but it helped a bunch!!! After 12 hours of playing with it I got it to idle stable. It hunts just a bit in gear but its livable. I will refuse to tune anything...
  4. Replies
    288
    Views
    307,038

    I have been using your transmission spread sheet...

    I have been using your transmission spread sheet since it came out with great results. This, this is awesome! Your a huge credit to our profession. I cant thank you enough. If you ever need cylinder...
  5. Replies
    5
    Views
    3,675

    2010 Camaro Supercharged idle issue

    Been messing with this for a couple days and I am exhausted. When you blip the the throttle the rpm goes up, comes down, seems to stabilize then it drops down to 450rpm and almost dies. I have played...
  6. Replies
    2
    Views
    2,369

    Nitrous slow shifting

    Did you ever get help on this? If not, I can help.

    Email me at [email protected]
  7. Replies
    18
    Views
    12,451

    Do you personally feel that with cams such as a...

    Do you personally feel that with cams such as a 232/245 113lsa that 21° is to much even if the MAF is close to the TB? With certain CAI I find that 21° is the only way to calm it down with high...
  8. Replies
    4
    Views
    4,023

    Yep, thats the problem. below is what I posted on...

    Yep, thats the problem. below is what I posted on another forum stating what we did to fit the other 2 clutches in the packs. The trans hits hard and firm now.


    The stock clutch clearances are...
  9. GMPP crate engine harness- MAP sensor problem

    I have run into a problem that hopefully some one here has run into as well. I dyno’ed tuned an LS3 engine on a Superflow dyno using an E67-ECM and a GMPP crate engine wire harness. It was an older...
  10. Replies
    4
    Views
    4,023

    They Are called Alto red Eagle clutches but they...

    They Are called Alto red Eagle clutches but they may very well be produced by Raybestos.
  11. Replies
    4
    Views
    4,023

    Major mystery with two 6L80s

    Never asked for help on this board before but I really need it now!:banghead:

    A friend and I recently purchased a complete rebuild kit with the Red Eagle double bonded clutches and Alto steals. I...
  12. Replies
    333
    Views
    265,740

    That was it! I copied a short cut to my desk top...

    That was it! I copied a short cut to my desk top and it was looking the DLL and could not find it. This must be a stand alone program.

    Thanks!
  13. Replies
    333
    Views
    265,740

    crash

    Followed the direction to a tee and everything works fine right up until I try to Generate Equations and then the program crashes. (see screen shot). I have tried to run the program as admin and with...
  14. Replies
    16
    Views
    18,177

    Lenovo

    My Lenovo T-510 with Win7 Pro has been rock solid stable and a great tuning platform with exception of the touch pad. Its very temperamental. I have been working with the settings and have about 80%...
  15. To anyone thinking this software is overwhelming...

    To anyone thinking this software is overwhelming at first my advice is to get on this forum and read Read, Read, Read, Read! I read every day on this subject and downloaded every PID, Histogram,...
  16. Replies
    2,288
    Views
    1,644,306

    Sticky: Hi from Texas!

    HI everyone, my name is Darin Morgan,

    I head up induction system R&D for Reher Morrison Racing Engines in Arlington Texas. My primary job is designing cylinder heads and over all induction systems...
  17. Replies
    2,288
    Views
    1,644,306

    Sticky: Still a newbie

    Hi guy’s. Name’s Darin Morgan

    My brother “Brad Morgan of Reher Morrison Racing Engines” and I have built every conceivable type and class of racing engine you can think of. I have been a...
  18. Will this work

    Will this work
  19. Replies
    31
    Views
    42,047

    Mine was flaring something awful after a...

    Mine was flaring something awful after a re-flash. I just increased line pressures 20psi and it eventually went away after about ten hard runs. I re-flashed about seven days after it went away and it...
  20. Replies
    1
    Views
    1,835

    Same problem

    You and me both . Contact support on beta issues.
  21. Replies
    33
    Views
    21,030

    I uploaded my new 2010 Camaro stock tune almost a...

    I uploaded my new 2010 Camaro stock tune almost a week ago as well. Have not seen it show up.

    Whats the deal?
Results 1 to 21 of 22