Search:

Type: Posts; User: BlackSS/SC

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    2,975

    OK thanks. What about the iat sensor when...

    OK thanks.

    What about the iat sensor when changing to this style maf?
  2. Replies
    3
    Views
    2,975

    Card style maf in 4" tube calibration?

    I have a cammed ls3 (swapped to 24x reluctor) in my 04 cts-v that I'm installing a homemade 4" intake with the ls7 card style maf tomorrow. It's tuned for the stock maf right now. Is there a...
  3. Replies
    5
    Views
    2,911

    Thanks for the reply. Has anyone been...

    Thanks for the reply. Has anyone been successful in tuning the flat response sensors to work correctly? Just wondering what other people did for tuning them.
  4. Replies
    5
    Views
    2,911

    I swapped around the 2 pins at the pcm to the...

    I swapped around the 2 pins at the pcm to the correct position today. I have the racetronix adapter harness to plug into the original wiring for the 2 signal wires. This harness has a ground at...
  5. Replies
    5
    Views
    2,911

    Yup Grande Prairie, AB. I will look into it...

    Yup Grande Prairie, AB. I will look into it more. I found the pinouts so good there. I assume I'd mirror the knock settings from a stock 6.2 file?
  6. Replies
    5
    Views
    2,911

    Ls3 into 04 cts-v - knock sensor help

    I am almost done swapping a ls3 into my 04 cts-v. I have the adapter harness to run the ls3 knock sensors instead drilling and tapping the block for the original ls6 knock sensors since they are a...
  7. Replies
    1
    Views
    1,958

    Driver Problems

    I have the MPVI Pro and have used it a lot, last time was about 3 months ago. Today my laptop with Windows 7 was dead so I tried to install on mt 8.1 laptop and it failed. Found my charger and...
  8. Replies
    1
    Views
    2,726

    Do I need Case RelearnÉ

    I swapped a 6.0l in for a 5.3l and it runs fine, no codes or anything and I've already got it tuned but just thought of this tonight. Do I have to do a case learn?
  9. Replies
    4
    Views
    4,152

    I did copy everything over from a 01 6.0l tune...

    I did copy everything over from a 01 6.0l tune but thought maybe GM has made some improvements on the newer stuff.
  10. Replies
    4
    Views
    4,152

    Anyone?

    Anyone?
  11. Replies
    4
    Views
    4,152

    6.0l LQ4 on 5.3 PCM

    I have a 6.0l in a Jeep, origianlly a 5.3l that spun a rod bearing. I just put the 6.0 in and was wondering. I looked up a stock 06 GMC Savana van since it's not drive by wire and my pcm is from a...
  12. Replies
    43
    Views
    18,062

    In the Power Enrichment table eq ratio vs rpm put...

    In the Power Enrichment table eq ratio vs rpm put 1.28 in the whole thing. That will make it command 11.5 afr under wot. You still need to get a wideband and tune it though.

    14.7/11.5 = 1.28
    ...
  13. Replies
    43
    Views
    18,062

    Get bigger injectors! Even on the stock pulley...

    Get bigger injectors! Even on the stock pulley you shouldn't go past 6500rpm on stock injectors. Also get yourself a wideband. Then you can watch it and feel safer while you're learing to tune.
    ...
  14. Replies
    8
    Views
    3,967

    Here's some more of what he said.

    Here's some more of what he said.
  15. Replies
    8
    Views
    3,967

    I will check that out. He did have a back one a...

    I will check that out. He did have a back one a last month. It was funny because it worked perfect for about 15 minutes of driving, it would switch just fine and then it would flat line. The car...
  16. Replies
    8
    Views
    3,967

    Oh yeah, O2 codes that are disabled: -P0137...

    Oh yeah, O2 codes that are disabled:
    -P0137
    -P0138
    -P0140
    -p0141
    -P0157
    -P0158
    -P0160
    -P0161
  17. Replies
    8
    Views
    3,967

    Here's what he wrote in an email: I'm at...

    Here's what he wrote in an email:

    I'm at work so I can't view the calibration right now, but where is this table located?
  18. Replies
    8
    Views
    3,967

    I'm going to go dial in the maf and ve again,...

    I'm going to go dial in the maf and ve again, eventhough the fuel trims are in check.

    It seems to be more of a heat soak thing I would say. It's been a while since I've played with this car so...
  19. Replies
    8
    Views
    3,967

    Lean at idle

    Hey guys, just need a little advise. I tuned a cammed LS1 and it seems to be running lean at idle. It happened once the car is totally warmed up. I've seen the gauge in the 18s for AFR. Sometimes...
  20. Doesn't look like you're logging knock retard. ...

    Doesn't look like you're logging knock retard. You have to set the config up to log "Total KR" because it's not setup for this car from the start.
  21. Replies
    26
    Views
    10,786

    Glad to hear! Thanks for the support! Just...

    Glad to hear! Thanks for the support!

    Just wondering, what would the benifits of having control over the SCIP sensor be?
  22. Replies
    26
    Views
    10,786

    I can't wait to play with this once it stops...

    I can't wait to play with this once it stops snowing! Damn snow in April!!! Crazy!! Is is possible to get access to the SCIP sensor tables?
  23. Replies
    26
    Views
    10,786

    Well that explains a few issues I've been having....

    Well that explains a few issues I've been having. I'm gonna have to go redo my tune today and see what happens.
  24. Replies
    26
    Views
    10,786

    So how low is everyone setting this? Would there...

    So how low is everyone setting this? Would there be any disadvantage to basicaly disable maf/ve blending?
  25. Replies
    19
    Views
    8,842

    Thanks Bill!

    Thanks Bill!
Results 1 to 25 of 110
Page 1 of 5 1 2 3 4