I just bought a 2002 Ford Taurus Id love to be able to TURBOCHARGE and tune. Maybe OLSD 3bar?
It only has 155hp, and it would take some boost to get to 400hp. I have attached the tune, and some...
Type: Posts; User: gn2beatu
I just bought a 2002 Ford Taurus Id love to be able to TURBOCHARGE and tune. Maybe OLSD 3bar?
It only has 155hp, and it would take some boost to get to 400hp. I have attached the tune, and some...
Cant you pull fuses for ABS/Stabilitrac when your at the track?
If your ECM is like most others, even when you press and hold the button, some stabilitrac is still there.
I couldnt load the tune now, but also dont forget to max ALL the tables under Engine Diagnostics, General, P0068.
This will keep the limp mode problem from happening when you up the boost. If you...
Also put the correct idle value in the first cell of the MAF curve, it will still use that one to try and start til MAF fails.
Did you scale the pressure shift areas in the tune as well. EX: Take value in the shift pressure areas by gear at 500ft/lbs and move to 250ft/lbs as your tune is scaled by 1/2, you need to move the...
If the ECM is an E40 from an LS2, then your better off with a 411 ecm IMO. Look at a 03-06 silverado harness and pcm.
Go to at least a 7series NGK plug, a 6 is NA territory for high compression LS2. This will lower EGT's and help with KR some. If your goona really lean on it may even need to go colder down the road...
Multiply your higher MAF tables by the % lean. So if your going WOT ~8000hz, then from 8000hz on up, multiply by the same amount. Example, your seeing WOT AFR of 13.5 and you want 12.5. Take...
Your AFR is 10.1 - that alone is enough to cause knocking (Rich Knock). Lean it out to 11.2 up to peak TQ, and to 11.5 by Peak HP. You also didnt mention what plugs your running, I hope its two...
Post the tune, log, and config so we can see whats happening.
I have been hearing about several people having this issue lately and 2 out of 3 times it was the sprocket causing the problem. On two the clearance space was not correct between the cam and the...
Look at 4:51 at your trims, they are anywhere from -13 to -20% off on one bank only. The other bank seems be positive +3 to +6 in most places. Something is wrong, get that fixed first. Notice how...
If that was a warm startup, it looks like a big vacuum leak to me. Unless you have a MONSTER cam.
It starts up rich, then goes dead lean, look at your O2 mv and your MAP values. Shouldnt be...
The longer away the sensor is, the longer it takes to respond. The TBSS sensor is right up front about 4" from the TB. When I ported my manifold, I cut it in two, removed the center pipe which...
Since you didnt post your tune I cant see what you have done, however that said - look under engine diagnostics, general, P0068 and max all the tables. I had a similar issue and you may be flowing...
PE is the enrichment table based on when the AFR changes by RPM and can be adjust by KPA as well. If this is your first time tuning, do two things. Google every table your dont know what is and read...
Form 3:00 to around 3:25 there are two differant idle areas where the O2's are doing opposite things. The first one is where the O2's hold for several seconds at 800mv + and the 2nd time they hold...
If your in closed loop you should not be running lean - as the load value on the engine isnt that great and the airflow going through the engine shouldnt be enough to spike EGT's or worry about KR as...
Did you change the TB scaler size? If its larger you need to lookup the correct value.
It's under Engine, Idle, Airflow, General, ETC area scaler.
Also to note, if it has been overported by a...
You may want to play with your Cutoff RPM Hyst value as well, depending on how fast you want it to resume after dropping RPM. Its in same area Engine -> Fuel -> Cutoff, DFCO, RPM Limits, Cutoff RPM...
Yes, pre cat, that was a type and fixed above.
That looks like real KR to me as it is happening under load. Even with the KR your still running ~26 degrees of timing which is good for an LS motor. Even the best of tunes with good gas usually...
x2 - check your pressure, if its dropping off that fast, then the regulators not holding pressure. It sounds like its the second prime thats enabling the start. You may want to try this as well, In...
Can you post a log of it happening and your config, so we see what you see?
Im sure you know this, but put wideband before cats if you have them.
Id recomend against tuning any WOT without a wideband.
I have seen narrow band swings from 780 to 1000mv all at the same...