Search:

Type: Posts; User: Dirthead Racing

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds; generated 39 minute(s) ago.

  1. Replies
    6
    Views
    4,075

    Also looking for injector data for these. I...

    Also looking for injector data for these. I don't like having to swag data in from other injectors.
  2. Tuning in, I've had surge I haven't been able to...

    Tuning in, I've had surge I haven't been able to get under control for a while as well. Like you say, hit brakes hard and adapt idle grab it and idles fine. Rolling into a stop, never know exactly...
  3. Replies
    458
    Views
    265,809

    I have to tune an 03 chevy with a Ford NP205...

    I have to tune an 03 chevy with a Ford NP205 T-case. The case ratio is 1.96:1. I can fake it in the 4 low tables or I could change the ratio if I had access to the tables. Can we get this added...
  4. Replies
    458
    Views
    265,809

    61230 I can't get these tables to show up. 4wd...

    61230
    I can't get these tables to show up. 4wd low is on every gm 4wd truck but the tables aren't available in 3.2 that I can find. I also can't find a spot where I would change the transfercase...
  5. Replies
    458
    Views
    265,809

    Do we get the 4 low tables without emailing...

    Do we get the 4 low tables without emailing support and the ability to change transfer case ratio with HPT V3.2?
  6. I would appreciate that. I'm still not sure why...

    I would appreciate that. I'm still not sure why it's not a super firm shift and I really don't want to do anything more with pressures than I have to. Thanks for taking the time to look.
  7. I think I found the TPS drop, the ETC limiter was...

    I think I found the TPS drop, the ETC limiter was at 5900. I'm still not sure if that'll correct the feel of the shift or not.
  8. Replies
    8
    Views
    2,825

    Fan settings worked by switching to analog...

    Fan settings worked by switching to analog cycling and doing what matty b suggested. Thanks!
  9. TPS drop during 1-2 shift. Slow 1-2 even with sonnex servo installed

    2005 5.3l/4l65e combo in a Jeep. During the 1-2 shift, the tps is dropping down to 40%. Sonnex servo installed and the shift still seems to take a long time. Can someone take a look and see what I...
  10. Replies
    8
    Views
    2,825

    Cool, I'll give it a try tomorrow night and see...

    Cool, I'll give it a try tomorrow night and see what happens.
  11. Replies
    8
    Views
    2,825

    Changed from serial cycling to analog cycling and...

    Changed from serial cycling to analog cycling and the fan settings made way more sense. Does this look better. Won't be able to try it for a day or two still but this seems to make way more sense.
  12. Replies
    8
    Views
    2,825

    I will give that a shot.

    I will give that a shot.
  13. Replies
    8
    Views
    2,825

    I didn't mention the lack of AC. There isn't an...

    I didn't mention the lack of AC. There isn't an AC pressure switch currently installed.
  14. Replies
    8
    Views
    2,825

    Jeep standalone 05 5.3 fan settings

    I'm not finding any tables that look like the fan tables that I'm dealing with. Using the VCM scanner we are able to turn fan 1 and 2 on and off but I haven't had any luck getting the fans to turn...
  15. I'm pretty sure I have to do the resister thing. ...

    I'm pretty sure I have to do the resister thing. I haven't worked on it in a couple of years. Within a couple hundred rpm has been close enough for the couple times I've driven it. I still want to...
  16. We haven't gotten the sensors swapped. I won't...

    We haven't gotten the sensors swapped. I won't be able to even look at it until June/July. Disappointing to say the least.
  17. What I don't understand is why the gen 4 06 TBSS...

    What I don't understand is why the gen 4 06 TBSS alum 6.0 KS tables and the Iron block 6.0 08 silverado KS settings are so far apart when the 04 SSR alum 5.3 and the 03 Silverado iron 5.3 are...
  18. Comparing 03SSR 5.3(alum) to 04SSR 5.3(alum), no...

    Comparing 03SSR 5.3(alum) to 04SSR 5.3(alum), no differences in KS settings. Compared 03 and 02 iron block 5.3 to each other, no differences in KS settings. Compare 03SSR alum 5.3 to 03 iron 5.3...
  19. Found 03 SSR used an aluminum 5.3, but resonant...

    Found 03 SSR used an aluminum 5.3, but resonant style sensors. I don't see any aluminum 6.0 that used a resonant style sensor at all so I don't think having it switched back over is going to gain me...
  20. http://delphi.com/manufacturers/auto/sensors/engin...

    http://delphi.com/manufacturers/auto/sensors/engine-and-transmission/diesel-and-gasoline/flat-response-knock

    So reading this, then reading the help menu in HP tuners, when I maxxed out all 4...
  21. Back to the top for the weekday crew. I'm open...

    Back to the top for the weekday crew. I'm open to suggestions!
  22. TBSS knock sensors on Gen3 pcm at wits end

    I'm trying to finish up helping a friend recover from a "professional" tune and harness setup and I'm at wits end with knock sensors. :banghead: This is a jeep stand alone Gen3 harness(red/blue...
  23. Good catch!

    Good catch!
  24. Anyone have a chance to look through that file...

    Anyone have a chance to look through that file and see if I have anything way off?
  25. Current file, he has a new TB on the way. Hope...

    Current file, he has a new TB on the way. Hope to get moving on it one it comes in. Here is the file I'm going to start with. Thoughts, comments, tips? I'm doing all work pro-bono so I'm not...
Results 1 to 25 of 58
Page 1 of 3 1 2 3