Search:

Type: Posts; User: dmuse76

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    234

    Fixed it guys. I refreshed the link in parameter...

    Fixed it guys. I refreshed the link in parameter access and it worked. I thought I had done that but apparently not. Sorry for the wasted post.
  2. Replies
    1
    Views
    234

    Need help with O2 DTCs

    Hoping someone can help. I have a standalone harness for a swap I have done. The harness doesn't have rear O2 sensor connections. I need to remove the DTCs but they seem to be blocked out(see...
  3. Fair point, I am used to Gen 4 stuff more so. For...

    Fair point, I am used to Gen 4 stuff more so. For clarity, I'm doing a swap and have a standalone harness for Gen 3 (99 5.3l) and it doesn't have rear O2 connections. Went to disable the DTCs and...
  4. Access to rear O2 delete still not seen after Training Course

    Sorry if this has been covered, I searched but didn't see it. I probably just missed it though.

    Do I have to upgrade to MVPI 2 or 3 to get full access after taking the training course? I took the...
  5. Thread: Logging issue

    by dmuse76
    Replies
    6
    Views
    3,410

    I repolled and that seem to fix everything but my...

    I repolled and that seem to fix everything but my wideband. I removed the channel and readded it (serial port > AEM > AEM AFR. It shows on the list as a channel until I click the red dot, then it...
  6. Replies
    5
    Views
    3,534

    I had the same issue with my scanner. I did what...

    I had the same issue with my scanner. I did what you suggested and got everything back but AFR (reported from wideband). Added the channel from Serial Port > AEM > AEM- AFR. When I click the red dot...
  7. Thread: Logging issue

    by dmuse76
    Replies
    6
    Views
    3,410

    Well, unfortunately that didn't fix it. Even...

    Well, unfortunately that didn't fix it. Even uninstalled and reinstalled Hp Tuner on my laptop. Same thing. Key on engine off, AFR listed in the left column and highlighted blue when I confirm it's...
  8. Thread: Logging issue

    by dmuse76
    Replies
    6
    Views
    3,410

    I'll try that and see what happens. I have closed...

    I'll try that and see what happens. I have closed out the scanner and reopened but haven't restarted my laptop. Hopefully it's that simple.
  9. Thread: Logging issue

    by dmuse76
    Replies
    6
    Views
    3,410

    Logging issue

    Having an issue logging. Data logger went from logging everything I had chosen to only logging MPH, and RPM. At first I noticed various things like STFT, or KPA, etc would drop out from log to log....
  10. Thread: Po606

    by dmuse76
    Replies
    2
    Views
    1,888

    It is. I've also set it to no error reported with...

    It is. I've also set it to no error reported with the same result. Just doesn't turn the check engine light on when hits limp mode.
  11. Thread: Po606

    by dmuse76
    Replies
    2
    Views
    1,888

    Po606

    Getting a PO606 code on hard launch, basically 0 pedal to 100% pedal. In between seems to be fine. Seems to happen more after the car has warmed up, but comes and goes and has happened at idle with...
  12. Replies
    5
    Views
    2,927

    sorry guys, motor is 436ci lsx, ls3 heads and...

    sorry guys, motor is 436ci lsx, ls3 heads and intake, 230/241 600/605 cam, 90mm throttle body, e38 ecm, converter is loose 3600, 4l80e trans. this is the new set up from a 6.0l with the same cam,...
  13. Replies
    5
    Views
    2,927

    Newbie question about tuning VE and MAF

    I've got the new set up running and I'm ready to tune it. I can't seem to find the post I saw detailing how to tune VE and MAF. Can someone please either share the link, or detail how to do it. As I...
Results 1 to 13 of 13