Search:

Type: Posts; User: planethax

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds; generated 23 minute(s) ago.

  1. Replies
    5
    Views
    3,285

    Are you able to login the customer section with...

    Are you able to login the customer section with your device ID?
  2. Make changes, load to pcm, re-read pcm and check...

    Make changes, load to pcm, re-read pcm and check if changes were made.
    Best way to verify.
  3. Replies
    3
    Views
    1,943

    Did you send file to support as the prompt said?...

    Did you send file to support as the prompt said?
    If it's not supported (definition/Vin not added) you wont be able to tune it.
  4. Replies
    6
    Views
    3,634

    More vehicle info may help. What does it say in...

    More vehicle info may help.
    What does it say in Main Table (not gauges)?
    Hpt should log as high as PCM puts out.

    posting same time as Bill
  5. Replies
    8
    Views
    3,492

    And the F body Osid is different than the Sierra...

    And the F body Osid is different than the Sierra Osid according to your screen capture.
  6. Replies
    8
    Views
    3,492

    You posted you COULD

    You posted you COULD
  7. Replies
    8
    Views
    3,492

    IIRC This is because you are trying to flash a...

    IIRC This is because you are trying to flash a Different OSID and Vin which wont work.
    I don't believe it would even work with a "write entire"
  8. Yes, if you have Beta installed, delete it. Then...

    Yes, if you have Beta installed, delete it.
    Then download latest Public release and install
    Then download latest Beta and install.
  9. Yes You need to update

    Yes
    You need to update
  10. I can verify that now. I did have to remove the...

    I can verify that now.
    I did have to remove the Beta and reinstall 2.24 then I was able to load the Beta with out overwritting.
    Now have both Current and Beta releases working side by side.
    Good...
  11. Replies
    10
    Views
    4,083

    Same result here. I also even created a new user...

    Same result here.
    I also even created a new user account (called beta) logged off current acount and intsalled Beta came back to current account and it was over written.
  12. Replies
    3
    Views
    2,521

    In the link Bill provided.

    In the link Bill provided.
  13. Replies
    1,138
    Views
    803,885

    Your best best is to contact support to make sure...

    Your best best is to contact support to make sure you have what you need to get a read of your NGC1 SRT-4 and send it in with an InfoLog
  14. Replies
    13
    Views
    8,973

    Have you emailed support at hptuners.com? You...

    Have you emailed support at hptuners.com?
    You may get a better answer with that.
    I would imagine if it was just the case of a simple calculation it would have been done already.
    I suspect the info...
  15. Personally I would start by deleting all old...

    Personally I would start by deleting all old copies of dotnetframeworkss then download and install latest.
    Then download latest HPtuners and install.
  16. Replies
    20
    Views
    6,616

    For now, open scanner (not log just scanner)...

    For now, open scanner (not log just scanner)
    Close Status Bit window, then open log.
    You can play log but do NOT open status bit window or you will crash.
  17. That doesn't mean it's good. I would check ckts...

    That doesn't mean it's good.
    I would check ckts with ohm meter from connector to Pcm
  18. I would start by checking the connector and...

    I would start by checking the connector and harness.
  19. Replies
    1
    Views
    1,663

    Some find it in other box with other papers etc....

    Some find it in other box with other papers etc.
    Did you get a customer login (interface number and password? )
    If not shoot an email to support at hptuners.com or the tuning school.
  20. Replies
    2
    Views
    2,940

    email support at hptuners.com

    email support at hptuners.com
  21. Thread: VCM Controls

    by planethax
    Replies
    7
    Views
    3,712

    Have you clicked on connect?

    Have you clicked on connect?
  22. Replies
    10
    Views
    10,886

    Set all VTD Dtcs to "3 No Error Reported"

    Set all VTD Dtcs to "3 No Error Reported"
  23. Thank Booster I appreciate it.

    Thank Booster I appreciate it.
  24. Replies
    20
    Views
    9,572

    This engine PCM works on alpha N fueling and has...

    This engine PCM works on alpha N fueling and has no maf.

    Do you have a wideband? If so what kind? Ill post a config for you to log with tomorrow when I'm at work and not on phone.
  25. 43357This is what I had started with for PE...

    43357This is what I had started with for PE settings
    but was changing around to see if I could get PE to stay
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4