Search:

Type: Posts; User: GXPLS4

Page 1 of 6 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    855

    E40 Not seeing boost on custom OS

    Has the cobalt boost sensor as many others before me, car will not see over 105KPA, applicable 2 bar parameters in scanner any help would be appreciated.7405374054
  2. Thread: Stinking E40!

    by GXPLS4
    Replies
    8
    Views
    3,051

    They don't brick just undo the battery cables for...

    They don't brick just undo the battery cables for a couple of hours hook back up and re write entire....it hapoens
  3. Annual bump for this perhaps with the new...

    Annual bump for this perhaps with the new software advancements we could get this??
  4. Replies
    4
    Views
    1,992

    No stumble though it pulls hard. I'm going to try...

    No stumble though it pulls hard. I'm going to try these changes out in a bit
  5. Replies
    4
    Views
    1,992

    I should've posted that. It's a 5.3 block stock...

    I should've posted that. It's a 5.3 block stock 243 heads cam is 222/227 113LSA
  6. Replies
    4
    Views
    1,992

    Idle issue after LJS Cam swap

    Trying to get idle under control at idle. I'm noticing in the logs I'm getting massive swings in advance which I think is causing the bucking at idle. Ive tried adjusting the usual things as per a...
  7. Replies
    3
    Views
    2,805

    I used the [email protected] one or whatever. ...

    I used the [email protected] one or whatever. At any route I got a new app key but I have no where to input the updated key on my windows 8.1 tablet
  8. I also delayed my shift speeds by 3mph so I can...

    I also delayed my shift speeds by 3mph so I can get more driveability out of it
  9. Yea you'll like it better city driving with out...

    Yea you'll like it better city driving with out tcc kicking in at 2nd gear
  10. You need to adjust your pattern a shift speeds...

    You need to adjust your pattern a shift speeds accordingly to what you want them to be. I also delay tcc engagement till 4th gear
  11. Replies
    3
    Views
    2,805

    application key invalid with tablet

    I have emailed support numerous times no reply so maybe someone can help me out. My tablet works great with the scanner full control and everything. However when I try to flash a tune file I get the...
  12. Replies
    7
    Views
    5,868

    Intresting Dave helped me with the same injector...

    Intresting Dave helped me with the same injector data however the numbers are off in spots. i might try your 12613412 file
  13. reset the codes first see if they come back....

    reset the codes first see if they come back. These would be common for a tb swap but since you're stuff is stock there might be some other factors at play.
  14. Replies
    7
    Views
    4,922

    You have a pm

    You have a pm
  15. Replies
    40
    Views
    18,908

    Regardless you'll need to re enter your map...

    Regardless you'll need to re enter your map values under engine -diagnostic-
  16. Replies
    6
    Views
    15,543

    Have you tried your cranking fuel vs. Fa ...

    Have you tried your cranking fuel vs. Fa table?a lot of people had sucess with 20% increase in fuel on the colder tenps
  17. Replies
    3
    Views
    2,480

    Correct What ECM is currenty installed in...

    Correct



    What ECM is currenty installed in the vehicle?You wont crank because of the diffrences in cranks, sou youll need that linglefelter 58x to 24xconversion kit for the crank sensor in...
  18. Replies
    17
    Views
    7,903

    Depends on the ecu

    Depends on the ecu
  19. Replies
    17
    Views
    7,903

    Zr1map won't work properly on e40 based pcm. We...

    Zr1map won't work properly on e40 based pcm. We have to use the cobalt one.
  20. My whole table is 100%

    My whole table is 100%
  21. You still have your Dynamic airflow set at 3600...

    You still have your Dynamic airflow set at 3600 and 3500. Bump them up to 8192 and 8191, and why is your throttle increase rat table set like that? 100% that fucker
  22. Replies
    5
    Views
    3,338

    Bumping this again

    Bumping this again
  23. Thread: etc area scalar

    by GXPLS4
    Replies
    2
    Views
    3,550

    I just dropped in the gto value in for etc area...

    I just dropped in the gto value in for etc area scalar. Never had a issue. I don't understand why you'd need excel to tell you that
  24. Replies
    3
    Views
    2,259

    Look in the tune repository start from there

    Look in the tune repository start from there
  25. Replies
    27
    Views
    21,791

    We already have hp tuners why not use it to the...

    We already have hp tuners why not use it to the max.
Results 1 to 25 of 139
Page 1 of 6 1 2 3 4