Search:

Type: Posts; User: Filapoosis

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    0
    Views
    1,716

    a/c segment swap?

    I have an isuzu box truck 6.0l with custom OS and was unable to tune,swaped with 06 truck pcm and all is well except a/c.Box truck has a pressure sensor not switch,is there any"fix"for this...
  2. Replies
    1
    Views
    1,578

    It has been a week and a half now, and I still...

    It has been a week and a half now, and I still have no response from tech. Can I get an idea of when this is going to be rectified?
  3. Replies
    1
    Views
    1,578

    1997 Corvette help

    I am having the normal issue with a 1997 Corvette PCM. I realize that the file needs to be sent to support, and I have already done this. Hoping that potentially someone can get the updated file to...
  4. Replies
    5
    Views
    3,161

    Just resent it, thanks for the help.

    Just resent it, thanks for the help.
  5. Replies
    5
    Views
    3,161

    Need Beta please

    Sent an email to support earlier today. Not trying to be worrisome but am in need of the new Beta for some 2010 Camaro tuning. Thanks in advance for any help.
  6. That's exactly what I needed!

    That's exactly what I needed!
  7. That works fine on the 4L60s, not working for me...

    That works fine on the 4L60s, not working for me with the 6L80.
  8. Replies
    23
    Views
    27,434

    6L80E, holding tranny in drive on the dyno

    What's the "trick" for keeping the A6 in gear on the dyno. Even using the paddle shifts won't leave the car in gear.

    Thanks in advance for any advice.
  9. 6L80E...holding trans in gear for dyno pulls

    What's the "trick" for keeping the A6 in gear on the dyno. Even using the paddle shifts won't leave the car in gear.

    Thanks in advance for any advice.
  10. Replies
    1
    Views
    1,520

    Flashed PCM, car will not recognize fobs

    This is the second time this has occured with an '06-'07 C6. Upon writing the PCM the car will not start and will not recognize the fobs, but I can still read/write the PCM. Has anyone else...
  11. Replies
    2
    Views
    2,197

    We're out of Raleigh and would be happy to help. ...

    We're out of Raleigh and would be happy to help. Mayhem Motorsports (919) 852-3766.
  12. Replies
    1
    Views
    3,171

    P2127 code after new throttle body?

    I recently installed a new from GM (unported) throttle body on my 2006 Corvette. I now have the P2127 code that will not reset. I have searched the forums and can not find any information relevant...
  13. Replies
    0
    Views
    1,307

    How is the fuel sender table figured out

    I put an aftermarket tank and the sender reads from 0-90 ohms. How do I adjust this in my file. Also how is the scale figured out on the sender charts.

    I attached my file.

    thanks
  14. Replies
    20
    Views
    8,877

    thanks it worked

    thanks it worked
  15. Replies
    20
    Views
    8,877

    You have a PM on the way, Keith.

    You have a PM on the way, Keith.
  16. Replies
    20
    Views
    8,877

    yes I am running a 3bar map sensor. When I pull...

    yes I am running a 3bar map sensor. When I pull the file out of my computer it pulls out the same file as above.
  17. Replies
    20
    Views
    8,877

    here is my config file with the changes on the...

    here is my config file with the changes on the max MAP value.
  18. Replies
    20
    Views
    8,877

    well I did the write entire and still dont have...

    well I did the write entire and still dont have that option. Anything else you can think of? Or can I send you my config and you take a look at it?
  19. Replies
    20
    Views
    8,877

    I went into the chart configuration and went to...

    I went into the chart configuration and went to chart 2 and changed the max KPA from 105 to 315. Will this work or will it still read incorrect?

    yea I did.
  20. Replies
    20
    Views
    8,877

    yes

    yes
  21. Replies
    20
    Views
    8,877

    I did exactly what you posted. I connected to the...

    I did exactly what you posted. I connected to the car. Went to display -> table. Then right clicked on the Manifold Air Pressure and deleted it. Then right clicked on that block hit insert. Went to...
  22. Replies
    20
    Views
    8,877

    when I right click and go to insert. It only...

    when I right click and go to insert. It only shows Manifold Air Pressure. It does not show the 2 or 3bar options.

    here is my scan file.
  23. Replies
    20
    Views
    8,877

    Scanner won't read 3bar

    I have a 3bar tune in my car and when we scan it the scanner only goes up to 1bar. I attached my file below.
  24. Thanks for the help Keith. Now I have another...

    Thanks for the help Keith. Now I have another question...I wanted to register all Gen III GM cars (30 credits), and it is only giving me the options for all LS1 cars (70 credits), single vehicle, or...
  25. PM sent

    PM sent
Results 1 to 25 of 63
Page 1 of 3 1 2 3