Search:

Type: Posts; User: 1slowbusa

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    1,378

    So, I have asked this question before a long time...

    So, I have asked this question before a long time ago and basically didn't get a good answer on how to dial it in. Russ K did post "The best open loop table is the stock 2004 truck 5.3." So I put...
  2. Replies
    9
    Views
    7,729

    Why is the spark constantly at 20 degrees. That...

    Why is the spark constantly at 20 degrees. That makes me think the idle adaptive spark control is not working but as far as i know the only way to disable that is with the vehicle controls in the...
  3. Replies
    27
    Views
    41,792

    Thanks guys for the reply. Basically what...

    Thanks guys for the reply.

    Basically what schpenxel said makes sense and he made it simple. This clears things up. Thanks again.
  4. Replies
    27
    Views
    41,792

    Maybe this is a stupid question but I cannot seem...

    Maybe this is a stupid question but I cannot seem to find an answer anywhere. Maybe one of you guys can answer this for me. I'm still a little confused on how to get the correct EQ Ratio when the...
  5. Replies
    1
    Views
    1,542

    That's a good question. If it was me, I...

    That's a good question.

    If it was me, I wouldn't try to worry about it right now and just get your wide band connected and tune it right. I would think if you change the MAF Fail Frequency, it...
  6. There is a lot to ready, of course. But, the only...

    There is a lot to ready, of course. But, the only way to learn is read or find a business that does training. Where exactly are you located?
  7. Replies
    4
    Views
    2,254

    What i am seeing in the tune you posted is that...

    What i am seeing in the tune you posted is that your LTFT are disabled and that you are always using filtered MAF readings. Do you have any scans as to where it is sluggish?

    But, I do agree with...
  8. Replies
    14
    Views
    6,147

    Where are you located?

    Where are you located?
  9. Replies
    6
    Views
    2,845

    Something else you may try is to reduce the PE...

    Something else you may try is to reduce the PE Thottle/Pedal Hot and Cold. Right now the table is set to 90 across the board. What if you set it to 45-55. This will activate the PE quicker to reduce...
  10. Replies
    6
    Views
    2,845

    Take a look at the at your lambda reading (in...

    Take a look at the at your lambda reading (in mobile_nitrous_run1) when you go to wide open throttle and you hit 3100 rpm, you are very lean. Your commanding 12.34 AFR and your wide band is reading...
  11. Replies
    6
    Views
    2,845

    At what RPM do you have the nitrous coming on? I...

    At what RPM do you have the nitrous coming on? I am guessing this is on a window switch? What size is the shot?
  12. Replies
    18
    Views
    6,254

    Email sent.

    Email sent.
  13. Replies
    17
    Views
    13,063

    Hey, post your stock tune, I would like to do a...

    Hey, post your stock tune, I would like to do a compare and see what all has changed.
  14. Replies
    18
    Views
    6,254

    PM me your email and I will give it a shot to try...

    PM me your email and I will give it a shot to try and get you going. Also, where are you located?
  15. Replies
    2
    Views
    1,472

    Unless you are running boost, you shouldn't see...

    Unless you are running boost, you shouldn't see anywhere over atmospheric pressure. The pressure changes depending on the altitude. Atmospheric pressure at sea level is 101.325 kPa. Now please keep...
  16. Replies
    18
    Views
    6,254

    Check your O2 Rich/Lean vs. Airflow settings....

    Check your O2 Rich/Lean vs. Airflow settings. They have been changed to something different than stock. Once you check and change, do another log and see if that corrects the problem.
  17. Replies
    18
    Views
    6,254

    What injectors are you running on this setup?

    What injectors are you running on this setup?
  18. Replies
    18
    Views
    6,254

    Post the tune. By looking at the O2 sensors...

    Post the tune. By looking at the O2 sensors voltage, you are dumping tons of fuel.
  19. Replies
    6
    Views
    3,132

    Are the injectors 42# at 4 bar? Is this an...

    Are the injectors 42# at 4 bar?
    Is this an automatic car?
    Where are you located?
    Who did the tuning on this? Post up your stock tune or PM me your email address and I will try to help you out....
  20. We really need to see some scans. HP tuner has a...

    We really need to see some scans. HP tuner has a great scanner and without seeing what the car is doing, it is hard for someone to help you.
  21. When I opened your file you posted in the first...

    When I opened your file you posted in the first thread, it is named 99 z28 kb tune. When I go to Calibration Details, it is saying that this file is from a 98 firebird/camaro. Something isnt right...
  22. Post your tune.

    Post your tune.
  23. Replies
    2
    Views
    1,829

    Go to Spark/Advance/IAT Spark-open the base...

    Go to Spark/Advance/IAT Spark-open the base table, this is what you are pulling for inlet air temps.
  24. Replies
    3
    Views
    2,001

    Posted this in the incorrect place. It is now...

    Posted this in the incorrect place. It is now posted correct location.
  25. Replies
    0
    Views
    1,298

    Configuring output enable/disable logic

    Hi,

    I know how to configure the output but as far as setting the trigger and disable trigger, this is where I have questions.

    Say I wanted to use an and logic, I wanted to activate my nitrous...
Results 1 to 25 of 103
Page 1 of 5 1 2 3 4