Search:

Type: Posts; User: chrisxiv

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    11
    Views
    7,159

    I'm having issues with the serial for my AEM...

    I'm having issues with the serial for my AEM wideband also. The Prolink works fine. But when I hook up to Serial, I am seeing a 18.3EQ ratio being read in the scanner. It just stays stagnant at...
  2. Replies
    56
    Views
    10,381

    I was under the impression that you needed to...

    I was under the impression that you needed to change the OS in order for the PCM to control the 3 wire AC pressure switch... I also thought that the pre-2002 trucks(maybe off one year) had a...
  3. Try logging less parameters

    Try logging less parameters
  4. Replies
    13
    Views
    3,556

    I have been using a Surface pro 4 for the past...

    I have been using a Surface pro 4 for the past year with MPVI2 without any issues. I recently noticed an electrical burning smell after plugging the dongle into the Surface. The HPT usb-c cable...
  5. Replies
    15
    Views
    5,144

    I see what you are saying. But the car would...

    I see what you are saying. But the car would actually start and run when it was brought to me. The issue was with the TCM mismatch(not shifting properly and doing all kinds of weird stuff). I looked...
  6. Replies
    15
    Views
    5,144

    This is exactly what i plan to do with an e38 ecm...

    This is exactly what i plan to do with an e38 ecm / 6l80 t43 tcm in a 1973 monte carlo a customer just brought to me to get running for him. The problem is mismatched parts and incompatibility...
  7. Can someone tell me if this tune file has Compatible ECM / TCM combination?

    This is a 6.2L 6L90 swapped 1972 Monte Carlo. The build was done by someone else about 95% complete. They brought it to me and I'm trying to figure out why the transmission doesn't want to shift. ...
  8. Listen to see if the fuel pump re-primes itself...

    Listen to see if the fuel pump re-primes itself when it fails to start. Could be your pump is not on during eng. cranking
  9. I noticed this almost right away after I applied...

    I noticed this almost right away after I applied the 3 Bar enhancement. I am running a autometer digital boost controller that I have piggybacked off the stock MAP sensor to get the boost readings.....
  10. Yes. I realize this. I didn't switch the OS w/o...

    Yes. I realize this. I didn't switch the OS w/o also switching the sensor as well.
  11. Thanks, I'll give that a try and see how it goes....

    Thanks, I'll give that a try and see how it goes. I'm just having a hard time grasping the fact that the truck ran well on this tune, but now it's not even close to wanting run.


    I also read...
  12. Im running the LS9 sensor. I think pn is...

    Im running the LS9 sensor. I think pn is 12592525 ?

    i know the VE is is extremely low on this tune. The truck ran very good on this tune, unless under high vacuum conditions. Only problem was...
  13. I just noticed something with the tune file.......

    I just noticed something with the tune file.... In editor, when I click the button for OS, nothing comes up. Its blank. So If I want flash to a custom OS or revert back to the factory GM operating...
  14. here's the 3 Bar tune. No VATS. The offsets i've...

    here's the 3 Bar tune. No VATS. The offsets i've been working with.


    I'm not ruling out a fault with the wiring, but Like I said, I've checked it multiple times.
  15. Replies
    4
    Views
    958

    could be a plug wire shorting out on the...

    could be a plug wire shorting out on the headers.... But first, I'd check your Crankshaft Pos sensor. Make sure its seated correctly and make sure the rubber grommet/seal is in there and in place. ...
  16. This is a 0411 P01 PCM with the red and blue...

    This is a 0411 P01 PCM with the red and blue connectors. Vehicle bin file started with a 1999 camaro M6
  17. Help... went from 3 Bar Custom OS to 2 Bar... Now won't start

    Just like the thread says. I was running a 3 bar custom Speed density OS. I got a 2 bar map sensor, wired it in place of the 3 bar. Confirmed the pinout was correct. The truck fired up, but ran...
  18. Replies
    6
    Views
    4,439

    Bringing this thread back from the dead... I?m...

    Bringing this thread back from the dead... I?m doing a LSA swap in a 69 Camaro with a 4L80e... customer has purchased all the PSI harness and has the same ecu/tcu combo mentioned in the OP...

    Has...
  19. I?m curious to know the same thing... has anyone...

    I?m curious to know the same thing... has anyone successfully ran a Flex Fuel OS with a manual transmission? I doubt its as simple as switching the drop down tab and disabling the DTCs. But maybe...
  20. very well explained. I completely agree. If I...

    very well explained. I completely agree. If I were to add another symptom into the leaking injector(s) issue I would add that it can quickly start to eat away or deteriorate the cats as well, if the...
  21. I?m having a similar issue with my Toyota pickup...

    I?m having a similar issue with my Toyota pickup swap. Running a t56 magnum as well and the readout on The scanner is way off.

    This isn?t that big of a deal for me since I?m running a GPS based...
  22. Replies
    2
    Views
    2,152

    Gotta love the support on here... I'm having...

    Gotta love the support on here...

    I'm having the same issue
  23. Replies
    211
    Views
    578,969

    Sticky: Just to follow up... I installed an older...

    Just to follow up... I installed an older installation I had stored on my other laptop(after uninstalling the VCM suite and the drivers that weren't working)... This seemed to fix the issue and I was...
  24. Replies
    211
    Views
    578,969

    Sticky: I also got a new laptop with windows 10....

    I also got a new laptop with windows 10. Downloaded the most recent version of the Software and drivers. I keep getting an error that says the drivers did not install properly because they are...
  25. Replies
    2
    Views
    1,113

    this would be nice option.

    this would be nice option.
Results 1 to 25 of 44
Page 1 of 2 1 2