Airflow / Variable Camshaft /Camshafts = None
That All ?
Type: Posts; User: Raul_Chile
Airflow / Variable Camshaft /Camshafts = None
That All ?
e38
0280158189 drilled:bigshock:
What is your opinion about load all 72# injector tables on attach file? (from ferocity02 of EFIlive.com)
FIC_873cc_83LB_4BAR_ev14_EFI_rev_02.xls ...
Yes, I have fuel pressure regulator(58psi) with Aeromotive fuel pump 340lph and return system
43745
43746
pic Injector Test Report
Bosch
72lb/hr rated at 43,5psi
Hi, I need help to scale 72# injectors on LY6 Stroker
This is my new setup
TSP 402 C.I.D.
LS3 CNC heads (pushrod, valve and springs stock)
Wiseco pistons
Melling Oil Pumps
340...
Hi, I have the same, the same problem¡¡
I have problem with my 2008 LY6. I have repinned a wire to pin 48. In HP tuners I have flashed it to "crank" and 15/15. Using resistors for a pull up signal...
Nice information. Can you help me with this?
I have problem with my 2008 LY6. I have repinned a wire to pin 48. In HP tuners I have flashed it to "crank" and 15/15. Using resistors for a pull up...
heeeelpppp please
I have speed fixed 255km/hr, I had have tried almost everything, please help. Attach tune file.
Best regards
Raul
Does it only table?
I have LY6 with T56. I need to modify tables and parameters in HPTuners to get in open loop.
Best Regards
Raul
We are two with the same problem:banghead:
Please any help
I don´t have connect VSS, remember T56 Corvette has not VSS sensor on tranny, It is on transaxle. Then I have not where put it.
Do you believe whether I don´t have VSS the PCM no shot signal by...
sorry, pictures adapter T56
I don´t have connected VSS, remember I installed old transmission T56 with tail housing, I out tail and put extension housing of transaxle corvette(see picture), this has not where to connect sensor...
1.-Yes, innitialy LY6 was 6L90 (Chevy 2500HD)
2.-repinned correct in Pin 48 C1
3.-I have manual transmission, T56 Corvette 1994
4.-Innitialy Allen Nelson re-programed PCM(tune hot-rod)
5.- I did...
more picture and videos
http://www.youtube.com/watch?v=qVZsbZSy5_A&list=UUs4tvDflTKNCT8YChlKCDbA&index=44
http://www.youtube.com/watch?v=oFWfE2DxvAU
.......
first specs and picture
Wrangler TJ
LY6-2008 (Out Silverado 2500HD)
T56 - Corvette 94
Adapter T56/D20 in house
Tranfer Case Dana 20
F44 front
F9 rear Detroit locker
33x12.50 Dunes Grappler
I have Wrangler TJ LY6/T56 with D20 transfer case for use Dunes Climb Up.
I don´t have problem in mode PE, temp 1200-1250°F full load, but not PE about 3000 to 4000RPM mid-load the 6.0 reach over...
I have problem with my 2008 LY6. I have repinned a wire to pin 48. In HP tuners I have flashed it to "crank" and 15/15. Using resistors for a pull up signal around 1K and a switched 12volt wire I get...