Search:

Type: Posts; User: bartender_77

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    29
    Views
    22,236

    Bill, im having the exact same issue, i was...

    Bill, im having the exact same issue, i was trying to tune and 18 mustang and was unable to tune it with 4.012 so i had to download thr latest vcm and no im stuck with a device that wont let me tune...
  2. Thread: No start

    by bartender_77
    Replies
    8
    Views
    3,744

    under System-General you still have the Clutch...

    under System-General you still have the Clutch interlock enabled, since this is a manual trans operating system, it needs to see the clutch being depressed otherwise it wont run, it could be...
  3. Replies
    19
    Views
    10,104

    ok, how much boost are your running? boost and...

    ok, how much boost are your running? boost and octane will dictate how much timing you can run, also when you say really rich, how rich is it, like below 10A/F or just under 11?
  4. Replies
    40
    Views
    30,444

    A its Voltage from the ecm, B is Ground, IAT...

    A its Voltage from the ecm, B is Ground, IAT sensor works with resistance hence the trick that we can do, so the ecm its looking for how much resistance it sees by sending voltage to the IAT sensor...
  5. Replies
    40
    Views
    30,444

    A and B its in reference to the 2 wires to go fro...

    A and B its in reference to the 2 wires to go fro the IAT sensor to the ECM, that's why when the relay its on it sends the signal to the ECM from the resistor instead of the actual resistance coming...
  6. Replies
    19
    Views
    10,104

    what your fuel pressure set at idle? those...

    what your fuel pressure set at idle? those injectors flow 80lb at 42psi of pressure so if your FP its set at gm's 58psi those injectors are going to flow a lot more so you need to adjust the tune for...
  7. Replies
    40
    Views
    30,444

    yes there is trick, look at the...

    yes there is trick, look at the pic,http://kwtmotor.com/up/files/64e3vlespsgu5j8w04w0.jpg that way it works is with a relay and resistor that you wire in a way that when the relay its on it bypasses...
  8. Replies
    3
    Views
    2,270

    do you have the latest beta? if not you might...

    do you have the latest beta? if not you might need it to read this tcm, but if you do, just pull the fuse for the tcm for a few secs, this will reset the tcm and that should take care of it
  9. Replies
    6
    Views
    4,286

    im also in need of version 2.20 of hptuners,...

    im also in need of version 2.20 of hptuners, anybody has a copy? i will really appreciate it, thanks!
  10. Replies
    1
    Views
    1,436

    2010 f150 aren't supported as far as i know, only...

    2010 f150 aren't supported as far as i know, only the 04-08 model years are covered, so im sure that the problem
  11. Replies
    10
    Views
    4,422

    that its almost as important as a wideband, i...

    that its almost as important as a wideband, i always, always check fuel pressure at WOT, its part of my tuning check list, it saves so many headaches, dont ask me how i know, a lot of time the high...
  12. Replies
    1
    Views
    1,616

    use this file to compare to your file, copy the...

    use this file to compare to your file, copy the trans differences to your file, it should shift fine if you make those changes, try it and report back, good luck
  13. Replies
    632
    Views
    394,617

    Me too! i tried many different logs and it keeps...

    Me too! i tried many different logs and it keeps saying the same thing, im also using the latest beta so that might have something to do?
  14. Replies
    57
    Views
    64,689

    this feature would be awesome :yay: i had this...

    this feature would be awesome :yay: i had this issues after cleaning a throttle body for a customer, and on some trucks the only way to relearn was to take it to the dealer and pay them $100 to do...
  15. Are the injetors firing at all? did you checked...

    Are the injetors firing at all? did you checked to see if they are pulsing when you crank it?
  16. Replies
    8
    Views
    9,805

    actually its really common on the TBSS for the...

    actually its really common on the TBSS for the switch to go bad, most likely thats what wrong, just replace it, they are not that expensive and easy to get to.
  17. Replies
    106
    Views
    79,786

    great post RWTD, :yay: you have always been of...

    great post RWTD, :yay: you have always been of great help here, i love reading your informative posts, and i do agree on the table raping thing, i have retuned a few cars that were done by big name...
  18. Replies
    4
    Views
    2,362

    by the way, you can always go to your customer...

    by the way, you can always go to your customer log in page and under credits there is a link to get your latest application key, just click on.......
    Click here to receive your latest application...
  19. Replies
    53
    Views
    36,726

    I totally agree, i mean, we all have ways of...

    I totally agree, i mean, we all have ways of tuning and no one is perfect and just because we think something its perfect it doesnt necessarily mean it is, but if im going to question some ones...
  20. Replies
    23
    Views
    23,601

    Just remember that he asking about a trailblazer...

    Just remember that he asking about a trailblazer SS that its quite heavy and that truck has an LS2 and in my experience those trucks in stock form or with with mild mods like an A/F of 12.4-12.5,...
  21. :D LOL funny guy

    :D LOL funny guy
  22. Replies
    15
    Views
    6,867

    Go to your.......Torque Management...

    Go to your.......Torque Management Table-General-ETC Limits-ETC TPS Max, on this table you have set everything to 0 why is that? you want this table at 100 not 0s, also the table below that one its...
  23. Replies
    62
    Views
    46,898

    Well that was really helpful, i have installed a...

    Well that was really helpful, i have installed a few set of fans but i could never figure out how to do the 2 speed deal, thanks!
  24. Replies
    62
    Views
    46,898

    ok so i get everything, but how did you get the...

    ok so i get everything, but how did you get the fans to come on at half the speed? thanks
  25. Replies
    3
    Views
    4,045

    Did you changed your fan settings from the PWM EV...

    Did you changed your fan settings from the PWM EV setting to Discrete? if not, thats your problem, look under ....System/Fans/General/Fan type and make sure that its changed to discrete.
Results 1 to 25 of 46
Page 1 of 2 1 2