Search:

Type: Posts; User: hexdummy

Page 1 of 7 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    6
    Views
    378

    Have you checked to see how fast your fuel...

    Have you checked to see how fast your fuel pressure drops off when you turn off the engine ? Sounds more like you have a faulty fuel pump check valve, that?s a very common issue and the symptoms are...
  2. Replies
    8
    Views
    2,274

    No current DTC's (there are some permanent DTC's...

    No current DTC's (there are some permanent DTC's I cannot clear) , DTC settings changed to mirror GMPP LT crate motor calibration settings.
  3. I did just recently compare all the DTC settings...

    I did just recently compare all the DTC settings to a manual trans GMPP cal and mirror those settings. This made no improvement in the drivability.
  4. @kras007 , can you provide an update on this...

    @kras007 , can you provide an update on this topic, were you successful ? I have the same setup and am looking for manual gearbox OS options.
  5. Replies
    8
    Views
    2,274

    Curious if anyone ever resolved this issue, same...

    Curious if anyone ever resolved this issue, same situation, rock crawler , TH350, no speed sensor. Initially it behaved the same as OP described , would start and idle occasionally ok, throttle would...
  6. changes needed to put E92 controller into "stand alone" or engine dyno mode

    Hello, I've had no luck trying to get the torque control to work as desired on a 2014 LV3 using a E92 controller installed in an off road buggy with a non-electronic controlled transmission. Yes,...
  7. Replies
    19
    Views
    2,696

    Please check your PM's.

    Please check your PM's.
  8. Replies
    19
    Views
    2,696

    Looking at your log and tune here is my...

    Looking at your log and tune here is my suggestions to start with:

    1. Change your log template to remove: battery volts, desired charging voltage, mil, add: vehicle speed, tps voltage, nv ratio if...
  9. Replies
    19
    Views
    2,696

    So, I realize you have been around in circles but...

    So, I realize you have been around in circles but start with the basics. It may not fix your drivability issues but if your minimum air flow is too low it certainly won?t help. You are looking for a...
  10. Replies
    19
    Views
    2,696

    Have you and how have you set you base or minimum...

    Have you and how have you set you base or minimum air flow ?
  11. Replies
    19
    Views
    2,696

    Post your log

    Post your log
  12. Replies
    19
    Views
    2,696

    Idle error vs. steps, i.e. target idle = 800 ,...

    Idle error vs. steps, i.e. target idle = 800 , actual idle = 880, ecu will subtract 8 steps from the iac. In this function the left column is idle speed error, the right column is the amount of steps...
  13. Replies
    19
    Views
    2,696

    Idle error vs. steps.

    Idle error vs. steps.
  14. Replies
    5
    Views
    2,270

    They all vary, saying it?s a stroker does not...

    They all vary, saying it?s a stroker does not really help. Stoker combination, deck height, fuel, CR, cam timing, cam specs , etc.. My general experience on mild stroker is that they often need less...
  15. Replies
    1
    Views
    670

    If you need help please PM me, I can help you...

    If you need help please PM me, I can help you with this.
  16. Replies
    10
    Views
    6,247

    Because they did not have Sentry key, they had...

    Because they did not have Sentry key, they had VTA.
  17. Replies
    6
    Views
    6,094

    Magnum engines had chronic issues with spark...

    Magnum engines had chronic issues with spark knock due to carbon deposits in the combustion chamber as well as from the actual burning of oil vapors due to the plenum gasket failing. Chrysler?s fix...
  18. Replies
    9
    Views
    2,453

    If your computer has four connector locations it...

    If your computer has four connector locations it is NGC, three = JTEC
  19. Replies
    21
    Views
    4,326

    You only made changes to the last load column in...

    You only made changes to the last load column in the fuel map, there are no changes in the area that the engine actually runs in.

    102044
  20. Replies
    21
    Views
    4,326

    The pulse width should directly translate to what...

    The pulse width should directly translate to what you put in the map. Basically under normal (idle and light throttle) conditions injector pulse-width = fuel table + battery offset + injector...
  21. Replies
    31
    Views
    16,741

    Default baro and min valid baro.

    Default baro and min valid baro.
  22. Replies
    31
    Views
    16,741

    jasond29, I have to disagree with your last post....

    jasond29, I have to disagree with your last post. Certainly if you are satisfied with your end result that's fine. I only want to clarify this point so that other people are not confused or...
  23. Replies
    31
    Views
    16,741

    It learns baro at key on and then relearns when...

    It learns baro at key on and then relearns when map exceeds baro or if you are going down in altitude, past a specific throttle angle. Problem is, this only works with a one bar map sensor. You will...
  24. Replies
    31
    Views
    16,741

    Although that student workbook is full of a lot...

    Although that student workbook is full of a lot of useful information and insights into the operation of the JTEC engine controller, the block diagram is definitely not good information . This...
  25. Replies
    31
    Views
    16,741

    Maybe HPT can add TORR as the native unit for map...

    Maybe HPT can add TORR as the native unit for map as well.
Results 1 to 25 of 163
Page 1 of 7 1 2 3 4