Search:

Type: Posts; User: joefus25

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    154

    the throttle follower tables under Idle/Airflow...

    the throttle follower tables under Idle/Airflow influence how the IAC stays open after throttle. I have had the best luck playing with decay(rpm) if IAC stays open too much.
  2. Replies
    1
    Views
    162

    did you ever figure out anything here?

    did you ever figure out anything here?
  3. I am wondering if you found a solution to the...

    I am wondering if you found a solution to the "warm" start issues you were having? I have had the same issues for a couple years but I have still not worked that part out yet. I am also wondering...
  4. Replies
    1
    Views
    130

    Most older mopars change speedo through ABS...

    Most older mopars change speedo through ABS module. Need a Snap on or something else to set "Pinion Factor"
  5. Replies
    2
    Views
    231

    Mine did work for a while.... it actually worked...

    Mine did work for a while.... it actually worked fairly well minus the fact it was missing som pid's. I imagine they will get it working again. I have noticed they have updated the tables in the...
  6. Replies
    2
    Views
    231

    mpvi2+ and JTEC+ scanner issue

    I have run into an issue when logging with the last beta install that broke something.

    I can not re-poll and I can not add channels. The repoll goes super fast and picks up nothing then of...
  7. Replies
    5
    Views
    2,937

    Still haven't found out anything new besides now...

    Still haven't found out anything new besides now I can't log again...

    I had a support ticket but all they had to tell me was that there's a lot of bus traffic..... no fix though...


    I hadn't...
  8. Replies
    7
    Views
    723

    Did you ever figure anything out on this? Mine...

    Did you ever figure anything out on this? Mine does weird stuff too and I don't understand why.
  9. Replies
    1
    Views
    985

    Did you ever figure this out? I am having...

    Did you ever figure this out? I am having similar issues. It will not upload my channel config to the device and it wont log anything standalone.
  10. Replies
    8
    Views
    1,950

    46re can only be "firmed up" mechanically. No...

    46re can only be "firmed up" mechanically. No electronic pressure control.
  11. Replies
    2
    Views
    382

    Thank you!!! I greatly appreciate it, glad it...

    Thank you!!! I greatly appreciate it, glad it was simple!

    Yes, I know the injectors are too small, I just need it to be able to pull in and out of the shop right now....
  12. Replies
    2
    Views
    382

    Will not rev above appx 1600 P59

    Hello, I have searched to no avail. Any help is appreciated.

    It idles ok but when pushing the throttle it will get to right about 1600 rpm and it seems to hit a fuel cut or something. If you...
  13. Replies
    60
    Views
    23,350

    Sounds like a worn TV valve in the valve body. ...

    Sounds like a worn TV valve in the valve body. How many miles on it? If it's got 150k+ talk to a transmission guy before you try to tune out something that will never work. Those transmissions are...
  14. Replies
    16
    Views
    4,739

    So far not supported. Not sure what it takes for...

    So far not supported. Not sure what it takes for different jtecs or otherwise but the PCM I have supports minimal scanner functions (beta).
    56040145AG (99 Dakota 5.9). Can not set sync, can only...
  15. Replies
    5
    Views
    2,937

    Anyways, seems that hpt can not read DTCs or log...

    Anyways, seems that hpt can not read DTCs or log PIDs on this ECU. Is there anything I can do to get some of these things added to the next beta or something? I am having a hard time tuning this as...
  16. Replies
    87
    Views
    51,366

    I also want to know whats up with these EMCs. I...

    I also want to know whats up with these EMCs. I have trouble logging useful info and figuring out what some tables even do. A bit confusing and I really wish they would put a bit more time into the...
  17. Replies
    5
    Views
    2,937

    Logging/tuning issues JTEC+

    I am not sure if I have done something wrong or my PCM is not fully supported but I have a few questions:
    1) I am unable to read DTCs in the scanner, but they will clear... Has anyone seen this...
  18. Replies
    10
    Views
    7,198

    I had duty cycles set to normal, then I changed...

    I had duty cycles set to normal, then I changed the DC to 99 just to see if it would apply correctly. Pulling trans back out this morning to make sure it's nothing mechanical.
  19. Replies
    10
    Views
    7,198

    Well, it is from tune file. I dont know what my...

    Well, it is from tune file. I dont know what my problem is either....Maybe there is issue with this pcm? Seems to be usual situation for what I work on...nothing works right.63646
  20. Replies
    10
    Views
    7,198

    63645 I did this and it still applies in 2nd...

    63645

    I did this and it still applies in 2nd and 3rd
  21. Replies
    10
    Views
    7,198

    Ignore some of the weird settings.... Was...

    Ignore some of the weird settings....
    Was testing. to see if anything was effected.

    By the way, it is a 2900 stall converter, 4t65e w/ transgo shift kit and did a progressive boost valve
  22. Replies
    10
    Views
    7,198

    01 4t65e converter

    I am having difficulty with converter lockup on this 01 regal. If anyone can help, let me know!
    Built this transmission, put a high stall converter in it. I can not seem to get 2nd and 3rd gears...
  23. Replies
    54
    Views
    39,361

    Haha I knew this would happen.... I do still...

    Haha I knew this would happen.... I do still look forward to HPT version of tunability on JTEC and if it's anything like the rest of their stuff, even though I am deep into the competitor's version,...
  24. Thread: JTEC Update?

    by joefus25
    Replies
    1
    Views
    1,528

    JTEC Update?

    Any news on JTEC/JTEC+? Honest answer here please, will it ever be supported? 1 year out? 2 years out? Wild guess? Never?

    Thanks HPT.
  25. Replies
    9
    Views
    4,873

    Yay!!! I can read my 99 5.9 pcm too! Good job...

    Yay!!! I can read my 99 5.9 pcm too! Good job fellers!
Results 1 to 25 of 42
Page 1 of 2 1 2