Search:

Type: Posts; User: madvette08

Page 1 of 18 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    20
    Views
    9,555

    D1/D2 Would only be used if there is 1 or 2 in...

    D1/D2 Would only be used if there is 1 or 2 in the shifter pattern.
  2. Replies
    20
    Views
    9,555

    If you want to know the shift pattern type. Look...

    If you want to know the shift pattern type. Look under Trans > Auto Shift Properties > General and you will see Shift Pattern Type.

    Pattern A = D
    Pattern B = S

    Cruise control references...
  3. There independent from the TCM TM.

    There independent from the TCM TM.
  4. Replies
    2
    Views
    2,035

    Bring the shift times up to .250 or .300. The TCM...

    Bring the shift times up to .250 or .300. The TCM will increase pressure to obtain quicker shift times.

    Set the Shift Time Factor and Shift Factor Adder to 1.00. Set the Adder Modifier table to...
  5. Replies
    10
    Views
    5,622

    CT Downshift disables the rev-matching for the...

    CT Downshift disables the rev-matching for the paddles and also slowing down to a stop. The CT Downshift under Tip-in Tgmgt is set to No Throttle. You will have a little delay when downshifting with...
  6. I always thought those tables had something to do...

    I always thought those tables had something to do with the torque converter during the shifts. But i could be wrong and that's about all i know on those lol.
  7. I would ignore the Cruise, Hot Table and...

    I would ignore the Cruise, Hot Table and performance on your vehicle. Cruise is used while Cruise Control is engaged, Hot is used when there is a Over Temp condition and Performance is used on trucks...
  8. Trans > Auto Shift Properties > Shift times >...

    Trans > Auto Shift Properties > Shift times > Shift Time Torque Adder Section: Try 0.250 msec for the Up Shift Normal and Up Shift Special tables. Try .200 msec for Down Shift Normal and Special...
  9. Replies
    2
    Views
    2,166

    Need to get 2.23 to see the other parameters....

    Need to get 2.23 to see the other parameters. Email [email protected] with you serial number.

    Ian
  10. You want to out her on the dyno?

    You want to out her on the dyno?
  11. Replies
    35
    Views
    33,773

    I understand the problem with doing a compare and...

    I understand the problem with doing a compare and copying over the Max Line Pressure table to another tune. I'm wondering if a pressure gauge was used to verify this problem with just changing the...
  12. Replies
    5
    Views
    3,153

    I had to click it lol...

    I had to click it lol...
  13. The Tuning School Advanced Seminar May 14th - 15th Tampa,FL

    Hey Everyone,

    Here is the detail PDF for the Seminar. http://www.thetuningschool.com/05_2011_adv_odessa.pdf

    The Seminar will be held at our Facility down in Tampa, FL....
  14. Replies
    4
    Views
    3,503

    Pattern Normal/A are Drive, Pattern B is Sport...

    Pattern Normal/A are Drive, Pattern B is Sport and the Tap Up/Tap Up Paddle Shifters have there own tables below Hot.

    Shift Pressures: Pattern X is Drive and Pattern Y is Sport and Paddle...
  15. Replies
    4
    Views
    3,742

    In the MAX line pressure table set the pressure...

    In the MAX line pressure table set the pressure to 290.1 from D1 to D6, also the Max Pressure B and Max Clutch.

    I attached my tune you can have a look at how i have the Shift Times and Base Shift...
  16. Replies
    30
    Views
    16,333

    How much boost are you running? 25 to 23 degrees...

    How much boost are you running? 25 to 23 degrees is a lot of timing for a FI car at WOT. I would pull 5 degrees of timing from above 0.88 cyl/airmass.
  17. Replies
    8
    Views
    3,489

    There is a timer for when it will go into Power...

    There is a timer for when it will go into Power Enrichment. Once your over 5000 rpm it will ignore the timer to go to Power Enrichment. On cars this timer is set to zero, so if your below 5000 rpm it...
  18. They need to use a DCT Transmission like in the...

    They need to use a DCT Transmission like in the BMW M3 or something like AMG 7-speed MCT Transmission. But only one can wish lol.

    Ian
  19. There are 2 spaces left on the dyno for anyone...

    There are 2 spaces left on the dyno for anyone wanting to attend the Seminar.

    Ian
  20. The Tuning School Beginners Live Seminar Twinsburg, OH April 16th-17th

    Hey Everyone,

    Here is the detail PDF for the Seminar in Twinsburg, OH http://www.thetuningschool.com/04_2011_beg_ohio.pdf.

    The Seminar will be held at the Mustang Dyno Facility. To register...
  21. Replies
    2
    Views
    2,708

    They are a skip shift feature, but only when you...

    They are a skip shift feature, but only when you are accelerating and let off the gas for some reason. You can but i wouldn't make them as aggressive as the rest of the shifts.
  22. We are having a Advanced in Las Vegas after SEMA,...

    We are having a Advanced in Las Vegas after SEMA, so i could see having one else where.
  23. Did you get to try WOT yet? Ian

    Did you get to try WOT yet?

    Ian
  24. 5 seats available in the Seminar.

    5 seats available in the Seminar.
  25. Replies
    5
    Views
    2,623

    If you can get to a Load Bearing Dyno, that would...

    If you can get to a Load Bearing Dyno, that would be best way to see if the Spark table needs to be optimized.

    On the Mustang Dyno we have, I use a feature called PRO Test. With this test you can...
Results 1 to 25 of 429
Page 1 of 18 1 2 3 4