Search:

Type: Posts; User: nick13618

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    36
    Views
    32,631

    Did this solve his problems? What were the part...

    Did this solve his problems?
    What were the part numbers?
  2. Replies
    5
    Views
    3,208

    any luck?

    Have you Had any luck with this? i'm trying to read my pcm, and it will only work in low speed.

    I've tried 2 different laptops, and tried pulling my neg terminal off and reseting the pcm to no...
  3. Replies
    199
    Views
    77,429

    what happened?

    What ever became of this discussion?
  4. well 1st off you need to post your cfg file so...

    well 1st off you need to post your cfg file so people can view what your viewing. 2nd, send a copy of your tune, your +50 on one side and -15 on the other side when you let off the gas, your scan is...
  5. Replies
    3
    Views
    2,004

    FYI: Bill

    I found a great way to search for the answers to my questions with out bugging you guys too much!

    when you open google type in what your looking for annd a space after then type in...
  6. Replies
    11
    Views
    4,063

    whats the difference between hi res and low res?

    whats the difference between hi res and low res?
  7. There is a ton of things that effect your...

    There is a ton of things that effect your commanded afr. you have to make sure your cmd a 12.8 afr or if its commanding a 11.
  8. i would take the PE table to All 1's, and see...

    i would take the PE table to All 1's, and see what it does,

    Also just watch the commanded afr in the scanner and the afr err


    If all else fails, i would download a tune from a fellow tuner and...
  9. i had the same problem, it has something to do...

    i had the same problem, it has something to do with the map sensor reading psi instead of kpa, it depends on what you have in the table.
  10. Replies
    5
    Views
    3,009

    this is a permanate write entire, correct?

    this is a permanate write entire, correct?
  11. Replies
    7
    Views
    4,392

    yes, if your running in true sd mode, no trims,...

    yes, if your running in true sd mode, no trims, no narowbands, maf ect, your ve table would determine your fuel ratio. not sure if if you can run open loop with pcm calculated arf adjustment for...
  12. Replies
    3
    Views
    2,251

    can you use one of the out puts to hook up to a...

    can you use one of the out puts to hook up to a digital gauge? i have an old fuel press gauge 0-100 that i want to use to show me my map. is this possable?
  13. Replies
    2
    Views
    1,688

    i have the same issue, both my widebands are...

    i have the same issue, both my widebands are reading ~14.3 average, and both front n/b are reading ~600 mv. eventhough i have a 14.68 commanded afr. if i use the scanner to command a 14.7 afr,...
  14. I have a similar problem, but only about 1 on the...

    I have a similar problem, but only about 1 on the stft, from 1 bank to another. stock lq4 motor. i read somewhere that you can use propane to find air leaks around injectors/ intake. watch your afr,...
  15. Thread: Truck Owners

    by nick13618
    Replies
    397
    Views
    301,867

    04 3500

    I've got a 2004 gmc 3500 single rear wheel. lq4, 4l80e. Headers, no cats, x-pipe true dual w/ flowmaster 40's. K&N cold air, TB spacer, Coolent line bypass, electric fans. 2 lc-1's, 2 narowbands....
  16. Replies
    2
    Views
    1,674

    Oh and new narowbands, 2 month old widebands,...

    Oh and new narowbands, 2 month old widebands, calibrated frequently.
  17. Replies
    2
    Views
    1,674

    I am going to keep adding fuel to the ve table,...

    I am going to keep adding fuel to the ve table, hoping that the pcm is over adjusting. there is nothing else i can think of.
  18. Replies
    2
    Views
    1,674

    I've got a couple newby ?'s

    both (2) of my wide bands are showing an afr of 14.1-14.4, and both my stock front narowband'2 are averaging ~600mv. i've got a 14.68 commaned arf, no power enrich, torque management, ect. sd tuning,...
  19. Replies
    9
    Views
    3,534

    ltft

    when i'm watching the ltft table, am i watching the average, the last or the highest value in the histogram? Is there a way to get the ltft table from the pcm?
  20. Replies
    4
    Views
    3,296

    same problem

    That fixed it for me too! Thanks
  21. Replies
    9
    Views
    2,951

    wait ....... how do you delete the boost pid?, i...

    wait ....... how do you delete the boost pid?, i figured out i had a bad user pid that it was looking at, instead of the "hptuners" MAP SAE". why does the sensor itself read half of what the pid...
  22. Replies
    9
    Views
    2,951

    I'm having the same problem, the histogram is...

    I'm having the same problem, the histogram is reading half of what the table data says it is, the sensor reads 40kpa, and the pid(map sae) is reading correctly, let me know if you had any luck, i am...
  23. Replies
    4
    Views
    2,329

    Well 1st off, i would disable it indefently for...

    Well 1st off, i would disable it indefently for any 2nd gear shifting, and possably in 3rd for perf. mode, but i like the way my truck pulls in 3rd w/ the t.c. locked up, a 1-1 ratio through the...
  24. Replies
    4
    Views
    2,329

    more info

    At what speeds are you seeing this, and what rpm/gear. is it all the time or just normal driving? what happens if you use your tow haul mode switch?
  25. Replies
    4
    Views
    3,279

    04 gmc fans

    I've got an 04 gmc 3500, that i put electric fans on, and i was wondering if there is an output from the pcm that controls the fans, even though it came with a fan on the pullys?
Results 1 to 25 of 30
Page 1 of 2 1 2