Search:

Type: Posts; User: AdsoYo

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    12
    Views
    850

    Lol your poor little ego. Either paying...

    Lol your poor little ego.



    Either paying attention is too hard for you or you're doing a horrible job at trolling. Probably the former. You pulled that whole statement out of your ass.
    ...
  2. Replies
    12
    Views
    850

    Doesn't take much for you to lose your composure...

    Doesn't take much for you to lose your composure does it? Didn't realize you're so fragile. I love how you say I'm on my own as if you're the only one on this forum who could possibly help. So you're...
  3. Replies
    12
    Views
    850

    To the top. Still open to ideas as to why the car...

    To the top. Still open to ideas as to why the car won't idle after a PCM reset.

    SiriusC1024 suggested the VE table but I'm running MAF-only. He also said my O2's weren't working correctly in the...
  4. Replies
    12
    Views
    850

    I don't think it was idle spark causing it...

    I don't think it was idle spark causing it because I ran it up to 30* before closed loop kicked in and it still wouldn't idle. Although if you look at spark as it gets close to stalling it swings...
  5. Replies
    12
    Views
    850

    I used the car to do errands today. As expected...

    I used the car to do errands today. As expected it would not idle on first start. I had to keep my foot in it until it hit closed loop then it idled fine. It drove and idled fine for the rest of the...
  6. Replies
    12
    Views
    850

    I copy/pasted the high and low octane tables from...

    I copy/pasted the high and low octane tables from a 2013 Corvette and then copy/pasted those numbers into the idle spark advance tables to match. Just did some reading and realized my mistake. I will...
  7. Replies
    12
    Views
    850

    Stalling after PCM reset

    Car has a crate LS3, 216/226-116+3 cam, 0411 PCM using a Lingenfelter box for cam/crank translation, drive by cable, T56. My issue is it will stall when idling and when coasting to a stop after a PCM...
  8. The log files have been added to the original...

    The log files have been added to the original post.
  9. I'll give it a try thanks!

    I'll give it a try thanks!
  10. I will tonight, working til 10 pacific time. ...

    I will tonight, working til 10 pacific time.



    I thought about increasing enable temps but stock has it at 91. Does LS1 vs LS3 and long tubes make that much of a difference? Would the base idle...
  11. Fuel leans way out when closed loop turns on, then normalizes

    This weekend was very cold where I live, around 20 degrees. I took the opportunity to tune areas of the open loop table I haven't been able to hit yet. I noticed when the car transitions from open to...
  12. In my 94 TransAm, I have 2 ALDL ports. When I did...

    In my 94 TransAm, I have 2 ALDL ports. When I did my 0411 swap, I bought a new harness for the engine that came with it's own ALDL port and the original I left in the car tucked under the dash. Now...
  13. Wow what a difference! Car behaved like its old...

    Wow what a difference! Car behaved like its old self, no wacky random ultra lean or rich swings. It was consistently slightly lean for a minute or two after a hot start but it always cleared right up...
  14. Guys these are some top quality posts. Tomorrow...

    Guys these are some top quality posts. Tomorrow before the lightning hits in the afternoon I'm gonna load up that injector data, tweak the scanner, and head out to do more driving. I'll report back.
  15. Yes I have it (I think). I wasn't comfortable...

    Yes I have it (I think). I wasn't comfortable using some tables because it assumes LS3 injectors are 41.7 lb/hr but I also found conflicting information that they are 39 lb/hr. So far I've been...
  16. Commanded AFR stays at 14.73 throughout my logs....

    Commanded AFR stays at 14.73 throughout my logs. Or is that not the proper/ correct "channel" I should be using? I noticed there's also a "commanded equivalence ratio" channel. If the weather isn't...
  17. That's what I thought too! Deleting the rear O2's...

    That's what I thought too! Deleting the rear O2's is so popular how is this problem not more ubiquitous? And this wasn't happening when I was tuning my LT1 with the same PCM and same software. The...
  18. No I didn't disable the MAF, I totally forgot...

    No I didn't disable the MAF, I totally forgot about needing to set the fail frequency way low to disable it. I mistakenly thought setting the "high rpm disable" to 9999 was enough.

    Along the line...
  19. Ah, setting the MAF fail frequency lower is a...

    Ah, setting the MAF fail frequency lower is a step I forgot. I was thinking since I set the high RPM disable to 9999 the MAF was out of the equation. Like I said, haven't done this in years. I didn't...
  20. I think see what you're saying. I'm using my...

    I think see what you're saying. I'm using my wideband for that purpose. I have a table in the scanner that records the AFR error and I copy/paste multiply by % half over and over until it's within 4%.
  21. Yes the point is to eliminate fuel trims when...

    Yes the point is to eliminate fuel trims when tuning the MAF and VE. Turn off trims, turn off power enrichment, find an empty country road or highway and start hitting all the cells. I used mostly...
  22. Thank you for that explanation! I knew there had...

    Thank you for that explanation! I knew there had to be something. I still have a question though. I did the 24x conversion on my old LT1 in 2014 and have been running this exact PCM ever since then....
  23. I'm using an LS1 MAP, MAF, O2 sensors, 0411 PCM...

    I'm using an LS1 MAP, MAF, O2 sensors, 0411 PCM with lingenfelter box
  24. Leans way out at idle, way rich on throttle, VE table looks rediculous

    There are so many issues, I feel like I must be missing something fundamental. I've spent the weekend attempting to tune my LS3 swapped '94 TransAm. It's a crate LS3 with a 216/226-116+3 cam. I have...
  25. Replies
    2
    Views
    593

    Wow that is a huge bummer. I feel like I bought...

    Wow that is a huge bummer. I feel like I bought my truck 1 year too late now.
Results 1 to 25 of 95
Page 1 of 4 1 2 3 4