Just checking I set it up right. I took the 3 volt max, and the 15 degrees max retard and divided the 3 by 15 which gave me .2 so in the user defined EIO I set up a voltage unit with a 0.2. Is this...
Type: Posts; User: Blazonic
Just checking I set it up right. I took the 3 volt max, and the 15 degrees max retard and divided the 3 by 15 which gave me .2 so in the user defined EIO I set up a voltage unit with a 0.2. Is this...
I am hooking up a LNC-2000 and wanted to monitor the timing retard function through the HP Tuners. The instructions of the LNC-2000 says it outputs analog 0 volts for 0 degrees and 3 volts for 15...
I have used raptors in the past, nice product. I just already had a spare shift light and was wondering if I could do it without having to purchase something else. Thanks for the recommendation tho
I was wondering if it is possible to run an external shift light of the computer. I noticed that there is a "Shift Light" area on HP Tuners which made this question arise. I just did a TH350 swap and...
I have tried a couple Z pak and also the Red 9 clutch system.
I buddy of mine thats been in the tranny business for 30 years, and I am there helping trying to learn/ cleaning parts.
well riding around today I got on it and burnt the 3-4 clutch pack. This is the third time I have burnt these. I have a lot of things in the tranny to prevent this, Trans-go HD 2, Boost valve, Billet...
I wonder if this is my problem....
:Taken from LS1Tech:
"Here's what's happening: With a heads/cam setup, the breathing potential of the LS1 often exceeds that of the Air Lid, MAF, or...
The stall is a 4300, and I only notice any problems at WOT. I have tried the desired time, and did the same thing. I will change it off 0 and see if it helps
The tranny has been out 8 times 3 of which less than 3000 miles on the car. Kept breaking input drums and output shafts. I can have it on the ground in 25mins so I am not worried about that... Just...
I tried to unlock it.
don't know how that happened. How do I unlock it?
I have a 00 Camaro that Flares (rpms rise while seeming to slip tranny) during the 2-3 shift. Some times it will shift fine, but most of the time it does this. I have brought my shift points down to...
I was changing the tune each time.
if your tranny has an HD2 transgo kit in it you can shift it manually even if the computer is telling it to shift. make sure your MPH and RPM are in the same area for your shift points.
Have a 4L80E in a camaro and made a couple hits at the track tonight. Was wondering if people are locking up the TCC when under WOT to help pull the car in 2nd and 3rd or only 3rd or if people are...
I am still kinda new at tuning this car and trying to learn as much as possible. I burnt 3-4 clutch pack again and was wondering if I am doing something wrong. I was told if you have a shift kit,...
I just recently bought a new laptop and trying to install HP on the new computer. I tried to load it on the new computer and update to the new 2.X which the drivers didn't work. I got on here and...
N/m guess I should have looked before posting.... seen another thread
I installed a LM-1 into the car today, the only problem I have is the HP tuners is reading 11.2 and the handheld part of the LM-1 is reading 14.4. I also don't have the serial cable or the software...
I licenced a 1 bar speed density tune and was wondering If it still uses the MAF or can it be removed or do I need a 2 bar etc. To do a speed density tune what else would I need to do? I have only...