Search:

Type: Posts; User: vltrb-0

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    5
    Views
    2,557

    Thanks for the replies the feedback is more than...

    Thanks for the replies the feedback is more than appreciated, i'm sorting out the plugs and setting up a few other small things to try rule out any false knock



    agree with the richness side of...
  2. Replies
    5
    Views
    2,557

    opinion on tune issues

    Wondering if someone could review my setup and give a 2nd opinion

    engine is stock 99 LS1, pac springs, single gt42 turbo, short 3.5" dump, powerglide, 2 bar SD, 7 psi gate spring, E85, siemens...
  3. Replies
    7
    Views
    11,978

    hard to tell what tables your specifically...

    hard to tell what tables your specifically talking about but the number 0.045 sounds me me like delta cyl air, which is change in g/cyl, if the g/cyl changes too quickly the ecu with pull timing as...
  4. Replies
    23
    Views
    16,962

    assuming this is correct info, really good post...

    assuming this is correct info, really good post the standard descriptions are fairly confusing
  5. Replies
    2
    Views
    2,584

    cheers for that i wanted to be sure as i wasn't...

    cheers for that i wanted to be sure as i wasn't 100% sure on the signal the dakota sensor put out


    i'll assume pin 50 is active just not used as this was the case for cooling fan output 2 in...
  6. Replies
    2
    Views
    2,584

    quick PCM wiring question

    2 questions

    I have a 99 LS1 ECU from a holden commodore in australia

    now i'm just trying to finish the wiring and i've been stalled on the speedometer

    1) i have pin 20 & 21 which are "HI"...
  7. Replies
    7
    Views
    4,170

    yep you can do that, the only thing im not 100%...

    yep you can do that, the only thing im not 100% on is if you have previously programmed your autometer gauge can you do a factory reset to 4000ppm

    i have the push button program type and im not...
  8. Replies
    7
    Views
    4,170

    programming doesn't matter, run the 2 mile...

    programming doesn't matter, run the 2 mile calibration for the autometer gauge, providing you have the vehicle speed sensor programmed correctly in the ecu then everything will read the same. ...
  9. your best bet is to read the forums, yes it takes...

    your best bet is to read the forums, yes it takes forever but in the long run you'll understand what your doing (well better than if someone hands it to you on a plate)

    consider if you have a...
  10. Replies
    5
    Views
    5,755

    i concur pin 42 as said log the status bit...

    i concur pin 42

    as said log the status bit post the log

    i had a very similar issue, post the log and we'll go from there
  11. Replies
    7
    Views
    4,150

    conditions would also alter your equivalence...

    conditions would also alter your equivalence ratios, best thing to do is scan and log and post differences
  12. Replies
    3
    Views
    1,813

    ok and how did you come to setting your tune up...

    ok and how did you come to setting your tune up for E85?

    i can't see a narrow band signal or wide band signal either which doesn't help
  13. Replies
    3
    Views
    1,813

    can you chuck up some info on the car itself,...

    can you chuck up some info on the car itself, e.g. fuel pressures, injectors, return or returnless, previous setup to E85

    where did this tune come from etc
  14. Replies
    7
    Views
    3,664

    worst case scenario and i do this with my...

    worst case scenario and i do this with my analogue pyro gauge

    video record the laptop and the gauge refer frames

    tedious but it works as a last resort
  15. for every pound of boost you put in your reducing...

    for every pound of boost you put in your reducing the amount of fuel you can deliver with the stock rails

    consider a return style fuel system and rising rate fuel regulator
  16. Replies
    8
    Views
    3,660

    what are these 'idle' and 'moving' tables i can't...

    what are these 'idle' and 'moving' tables i can't find any reference to them
  17. Replies
    8
    Views
    3,660

    i'd also like clarification on this as far as im...

    i'd also like clarification on this as far as im away i only have a primary VE table
  18. Replies
    8
    Views
    3,660

    little update for those interested stripped...

    little update for those interested

    stripped the extension housing off the glide, i got the glide from the states seems you guys like to remove the speedo drive gears for no apparent reason :usa:
    ...
  19. Replies
    10
    Views
    6,266

    judging from this your device volt range is 5...

    judging from this your device volt range is 5 (0-5v)

    your afr range is 10 (20-10)

    your offset is 10

    never used an AEM but assure your using the correct output some gauges have a 0-1.1v output
  20. Replies
    10
    Views
    6,266

    print screen it and paste it into paint and save...

    print screen it and paste it into paint and save as a jpeg and upload

    take a pic of the function in the user defined pids
  21. Replies
    10
    Views
    6,266

    i can't read that config, can you just post a...

    i can't read that config, can you just post a screen pic of the function your using

    your wb output voltage is suppose to vary with respect to afr
  22. Replies
    19
    Views
    7,681

    looks from the log your power enrich comes in at...

    looks from the log your power enrich comes in at 60% as per 5m38s
  23. Replies
    8
    Views
    3,660

    i'll have to check the gearbox for a provision...

    i'll have to check the gearbox for a provision for a speedo as i haven't noticed one before, might have been blanked with a welsh plug

    assuming i can use a speedo, any idea what would be the best...
  24. Replies
    8
    Views
    3,660

    ramifications of park/drive

    any experts out there who know what problems i may have from not selecting between the two?

    to detail i have a power glide with no feed back to the ECU, i could possibly hook this up through my...
  25. Replies
    12
    Views
    5,420

    yep from your scanner delete the map PID and then...

    yep from your scanner delete the map PID and then re add the 2 bar map sensor pid
Results 1 to 25 of 82
Page 1 of 4 1 2 3 4