Search:

Type: Posts; User: TRENT

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    8
    Views
    4,037

    Thanks

    Thanks
  2. Replies
    8
    Views
    4,037

    CTS-V whats the hot set up

    Has anybody played with a 2011 cts-v I have a customer that wants to play with his looking for the best bang for his money like pullys add on things like that thanks :shrug::shrug::shrug:
  3. Thread: 1998 corvette

    by TRENT
    Replies
    0
    Views
    1,156

    1998 corvette

    I have a 98 vette I install a cam in it and when I set it up to do a VE tune and turn off the mass and get a 103 code I get a 108 map code to has anybody run into that because with to 108 code the...
  4. Replies
    0
    Views
    1,028

    Idle on 98 Corvette

    I'm getting beat down on a 98 corvette with etc and a stock motor with cam I might have over look on this board but can someone lead me to the how to for early ls1 with etc idle tuning if so thanks
  5. Replies
    2
    Views
    1,804

    08 Vette with 80lbs injector

    I have a 08 vette with a supercharger it has 80lb injectors Ihave the tune close but my maf is to low and it will interfear with the load can someone help me with this tune to scale the injector...
  6. Thread: 80 lb injectors

    by TRENT
    Replies
    0
    Views
    1,301

    80 lb injectors

    Can any Body help I've got a 08 vette SC I install 80lb injector does anybody have the cal on the injectors IFR vs Pressure Delta
  7. It might idle fine for a day or two and you pull...

    It might idle fine for a day or two and you pull in somewhere and in will just cut off.The tb works good
  8. 2007 Trailblazer SS will not idle at times / new cam / new tune

    Has anybody installed a cam and started having problems with idle only at times. The tune works good you can not ask for it to crank up or idle and better most of the time. you can flash a new tune...
  9. Scanner reads some pid wrong or does not read at all

    Can some body look at my config file and tell me what I have wrong It reads the map 0 or -65 the IAT and the coolent -40 o2 mv read nothing no LTFT or STFT thanks I have cleared the scanner and...
  10. Replies
    1
    Views
    2,682

    Ls1 Dual Fans On Trailblazer Ss

    I have a 07 trailblazer SS and put dual ls1 fans on it I found all kind of info on how to program but can any body tell me when you wire your two relays up what pcm pins do you use.I know that pin is...
  11. Replies
    7
    Views
    3,049

    I dont have but one custom pid and it is the WBO2...

    I dont have but one custom pid and it is the WBO2 I will remove it and replace it to see if that works
  12. Replies
    7
    Views
    3,049

    #3 LTFT primary VE vs RPM vs MAP (kpa) during...

    #3 LTFT primary VE vs RPM vs MAP (kpa) during scanning it shows rpm and LTFT but on the map side it stays on the 15 row It does that on all hist that have MAP I have change the MAP setting and it...
  13. Replies
    7
    Views
    3,049

    Here are both thanks

    Here are both thanks
  14. Replies
    7
    Views
    3,049

    histograms will not work for LTFT

    I have tryed everything but must be missing something in the histograms I can not get my MAP kpa to work it works in tables charts and gauges the histograms work but not with any of them that has to...
  15. Thread: 06 Cad Cts V6

    by TRENT
    Replies
    1
    Views
    2,012

    06 Cad Cts V6

    Does anybody have any tuning info one a 06 cad cts V6 3.6 or can somebody point me in the right dir. thanks here is the file in looks like it does not have mini tables and no transmission table is...
  16. Thread: 2010 Lmm Tune

    by TRENT
    Replies
    2
    Views
    2,667

    2010 Lmm Tune

    Can anybody that is very good with a diesel look at this tune and see if I need to change or look at It runs good but at WOT it acts like it is runing out of fuel and the pcm keeps going to 0% fuel...
  17. Thread: 09 Lmm

    by TRENT
    Replies
    2
    Views
    2,888

    09 Lmm

    Has anybody had any problem reading the pcm/tcm. I have tried it in high speed and without and it is taking over and hr and will not finish it is moving very slow or is it my laptop but Im not having...
  18. Thread: Injectors

    by TRENT
    Replies
    2
    Views
    1,804

    Injectors

    Does anybody know what size inj. this is at 60 psi 722-1w08248
  19. Replies
    3
    Views
    2,184

    Yes it is in beta 2.23 I think this vette has...

    Yes it is in beta 2.23 I think this vette has maga supercharger 7.5 lb and I have a 9.5 lb pulley but I'am going to get that lean spot out first and I know I have to add more fuel 5500 and up.
  20. Replies
    3
    Views
    2,184

    08 Vette Lean Between 2500 & 3500

    Any ideas on why PE comes in and then it gos lean at 2500 and then goes back at 3500
  21. Replies
    0
    Views
    1,226

    Jeep With Ls Motor

    I keep getting fail cal when flashing computer.Need help The odb2 connector is wired with serial to pin 2 4&5 are ground and 16 power It will read the pcm but will not write to the pcm
  22. Bob It would be nice If I could get the VE and...

    Bob It would be nice If I could get the VE and MAF supplement that you include now in the beginners course and promised to all the people that took the first beginners course. You have said that you...
  23. Thread: Bad Startup

    by TRENT
    Replies
    1
    Views
    1,482

    Bad Startup

    Can Somebody look and this tune and see what I am missing 05 vette CNC heads 232/234 cam. Cold start is good but hot start not unless you open tv. added start up air and then bad idle.
  24. Replies
    9
    Views
    4,110

    I guess I'm getting old. Thanks

    I guess I'm getting old. Thanks
  25. Replies
    9
    Views
    4,110

    Bill what is AFAIK

    Bill what is AFAIK
Results 1 to 25 of 93
Page 1 of 4 1 2 3 4